F 『
E C F M E
E E
E 56-5B E
E E
E. Do this Test:
(1) Do a FADEC Ground Test (Engine Motoring) (Ref. TASK 73-29-00-710-040).
(2) Do a minimum idle check (Ref. TASK 71-00-00-710-006) and do a check for leaks (Ref. TASK 79-00-00-210-003).
(3) stop the engine and do the steps below:
(a) On the left or right MCDU, get the SYSTEM REPORT/TEST.
(b) Push the NEXT PAGE mode key : a new SYSTEM REPORT/TEST page comes into view.
(c) Push the line key adjacent to the ENG indication : the SYSTEM REPORT/TEST ENG page comes into view.
(d) Push the line key adjacent to the FADEC 1A(1B) for engine 1.
(e) Push the line key adjacent to the FADEC 2A(2B) for engine 2.
(f) Push the line key adjacent to the LAST LEG REPORT.
(g) Make sure that the message "EOT SENS,J13,ECU" is not in view.
(h) Do the EIS stop procedure: (Ref. TASK 31-60-00-860-002).
5. Close-up
________ Subtask 79-31-40-862-051
A. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
F 『 EEFF : ALL E Page 40779-31-40
E E Feb 01/98 E E ECES E Subtask 79-31-40-410-054
F 『
E C F M E
E E
E 56-5B E
E E
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 40879-31-40
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
OIL TEMPERATURE SENSOR - INSPECTION/CHECK
_________________________________________ TASK 79-31-40-210-002 Visual Inspection of the Oil Temperature Sensor
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific bristle brush No specific warning notice
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R Material No. Material No. CP1039 CP2010
Material No. CP2011
R R R R R R R R R R Material No. Material No. Material No. Material No. Material No. CP2559 CP2560 CP2566 CP2584 CP2656
*
acetone (Ref. 70-30-00)
*
white spirit (Ref. 70-30-00)
*
Stoddard solvent (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
*
mag-chem skysol (Ref. 70-30-00)
F 『 EEFF : ALL E Page 60179-31-40
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
R 79-31-40-000-002 Removal of the Oil Temperature Sensor (IDG Cooling
R System Control Sensor)
R 79-31-40-400-002 Installation of the Oil Temperature Sensor (IDG
R Cooling System Control Sensor) 79-31-40-991-300 Fig. 601
3. Job Set-up
__________
Subtask 79-31-40-941-052
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure. 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(62)
