Subtask 79-21-30-010-051
 B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 4. Procedure
_________
 Subtask 79-21-30-020-050
 A. Removal of the visual indicator. R R PRE SB CFM 79-0014 R R (Ref. Fig. 401/TASK 79-21-30-991-301) R R POST SB CFM 79-0014 R R (Ref. Fig. 402/TASK 79-21-30-991-304) R R END SB CFM 79-0014 R
 (1) Disconnect the connectors (10) and (20) from the visual indicator (60). Use soft-nose connector pliers only if necessary.

 (2) Remove the two nuts (30) and the two bolts (40).

 (3) Remove the visual indicator from the engine.

 (4) Put blanking caps and blanking plugs on the connectors and the receptacles.

 F 『 EEFF : ALL E Page 40279-21-30
 E E Nov 01/02 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

R  Visual Indicator (Pre SB CFM 79-0014) Figure 401/TASK 79-21-30-991-301
 F EEFF : E E ECES  ALL  『E 79-21-30EEE Page 403 Nov 01/02

R R  Visual Indicator (Post SB CFM 79-0014) Figure 402/TASK 79-21-30-991-304
 F EEFF : E E ECES  ALL  『E 79-21-30EEE Page 404 Nov 01/02

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 79-21-30-400-001
 Installation of the Visual Indicator
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific warning notice
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. CP2101  USA MIL-T-5544
 graphite grease (Ref. 70-30-00)

 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
 79-21-30-991-301 Fig. 401

R 79-21-30-991-304 Fig. 402
 F 『 EEFF : ALL E Page 40579-21-30
 E E Nov 01/02 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 3. Job Set-up
__________
 Subtask 79-21-30-860-050
 A. Aircraft Maintenance Configuration
 (1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.

 (2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).

 Subtask 79-21-30-010-053
 B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 4. Procedure
_________
R
 Subtask 79-21-30-420-050
 A. Installation of the visual indicator R R PRE SB CFM 79-0014 R R (Ref. Fig. 401/TASK 79-21-30-991-301) R R POST SB CFM 79-0014 R R (Ref. Fig. 402/TASK 79-21-30-991-304) R R END SB CFM 79-0014 R
 (1) Lubricate the threads of two bolts (40) with graphite grease (Material No. CP2101)

 (2) Attach the visual indicator (60) to the bracket (50) with two bolts

 (40) and two nuts (30).
 F 『 EEFF : ALL E Page 40679-21-30
 E E Nov 01/02 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (3) TORQUE the nuts (30) to between 95 and 110 lbf.in (1.07 and 1.24 m.daN).

 (4) Remove the blanking caps and plugs from the connectors and the receptacles.

 (5) Connect the connectors (10) and (20) to the visual indicator (60).

 5. Close-up
________ Subtask 79-21-30-410-051
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(51)