F 『 EEFF : ALL E Page 62279-00-00
 E E Aug 01/03 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E E E R Subtask 79-00-00-010-074

R B. Open the fan cowls doors: (Ref. TASK 71-13-00-010-040) R FOR 1000EM1 R 437AL, 438AR R FOR 1000EM2 R 447AL, 448AR.
R 4. Procedure
_________
R (Ref. Fig. 601/TASK 79-00-00-991-301, 605/TASK 79-00-00-991-307, 606/TASK R 79-00-00-991-308, 607/TASK 79-00-00-991-309, 608/TASK 79-00-00-991-310)
R Subtask 79-00-00-020-052
R A. Remove the Electrical Master Chip Detector (EMCD) as follow: R (Ref. Fig. 601/TASK 79-00-00-991-301)
R (1) At the same time, push and turn the EMCD plug one quarter of a turn R counterclockwise.
R (2) Disengage the EMCD from its housing.
R Subtask 79-00-00-280-054
R B. Check of the chip detector system. R (Ref. Fig. 606/TASK 79-00-00-991-308) R R PRE SB CFM 79-0014 R
R (1) Check the functioning of the chip detector including visual indicator R pop out response.
R NOTE : Visual indicator must be energized by 28 volts Aircraft power
____ R only (Ref. TASK 24-41-00-861-002).
R (a) Bridge the gap between the 2 magnet poles with a metallic wire R jumper or any metallic piece for a minimum of 1 seconds.
R (b) Do a visual inspection of the visualindicator red pop out, it R must extend (extension time < 1 second).
R (2) If the red pop out indicator is extended:
R (a) De-Energize the Aircraft Electrical Circuits from the External R Power (Ref. TASK 24-41-00-862-002).
 F 『 EEFF : ALL E Page 62379-00-00
 E E Aug 01/03 E E ECES E F 『 E C F M E E E E 56-5B E

R Illustration of the Inspection of the EMCD and hardware associated

R  Figure 605/TASK 79-00-00-991-307
 F EEFF :  ALL  『E 79-00-00 Page 624 
E  E  Aug 01/03
 E  E
 ECES  E

 F 『 E C F M E E E E 56-5B E

R Illustration of the Installation of the gap between the 2 magnet poles

R  Figure 606/TASK 79-00-00-991-308
 F EEFF :  ALL  『E 79-00-00 Page 625 
E  E  Aug 01/03
 E  E
 ECES  E

 F 『 E C F M E E E E 56-5B E

R Illustration of the visual indicator functional check (PRE SB 79-0014)

R  Figure 607/TASK 79-00-00-991-309
 F EEFF :  ALL  『E 79-00-00 Page 626 
E  E  Aug 01/03
 E  E
 ECES  E

 F 『 E C F M E E E E 56-5B E

R Illustration of the visual indicator functional check (POST SB 79-0014)

R  Figure 608/TASK 79-00-00-991-310
 F EEFF :  ALL  『E 79-00-00 Page 627 
E  E  Aug 01/03
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E 

R (b) Do the resetting of the visual indicator (Ref. TASK 79-21-30-440-R 001).
R (c) No further action is required, do the step H. Install the EMCD
R (3) If the red pop out is not extended:
R (a) De-Energize the Aircraft Electrical Circuits from the External R Power (Ref. TASK 24-41-00-862-002)
R (b) Do the step EMCD system functional check. R R END OF PRE SB CFM 79-0014 R
R Subtask 79-00-00-280-058
R C. Check of the chip detector system. R (Ref. Fig. 606/TASK 79-00-00-991-308) R R POST SB CFM 79-0014 R
R (1) Check the functioning of the chip detector including visual indicator R pop out response.
R NOTE : Visual indicator must be energized by 28 volts Aircraft power
____ R only (Ref. TASK 24-41-00-861-002).
R (a) Bridge the gap between the 2 magnet poles with a metallic wire R jumper or any metallic piece for a minimum of 45 seconds.
R (b) Do a visual inspection of the visualindicator red pop out, it R must extend (extension time from 10 to 45 seconds).
R (2) If the red pop out indicator is extended:
R (a) De-Energize the Aircraft Electrical Circuits from the External R Power (Ref. TASK 24-41-00-862-002).
R (b) Do the resetting of the visual indicator (Ref. TASK 79-21-30-440-R 001).
R (c) No further action is required, do the step H. Install the EMCD
 F 『 EEFF : ALL E Page 62879-00-00
 E E Aug 01/03 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
R (3) If the red pop out is not extended:

R (a) De-Energize the Aircraft Electrical Circuits from the External
R Power (Ref. TASK 24-41-00-862-002)

R (b) Do the step EMCD system functional check.
R
R END OF SB CFM 79-0014
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(15)