(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 40779-21-30
E E Nov 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 79-21-30-000-002
Removal of the DPM Harness
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific blanking plugs
No specific soft-nose connector pliers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors R 79-21-30-991-302 Fig. 403
3. Job Set-up
__________
Subtask 79-21-30-941-052
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
F 『 EEFF : ALL E Page 40879-21-30
E E Nov 01/02 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 79-21-30-010-052
B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
4. Procedure
_________
R (Ref. Fig. 403/TASK 79-21-30-991-302)
Subtask 79-21-30-020-051
A. Removal of the DPM harness
(1) Disconnect the DPM harness from the visual indicator.
NOTE : Disconnect the magnetic chip detector harness from the DPM
____ harness receptacle (150). Use soft-nose connector pliers only if necessary.
(2) Remove the DPM harness as follows:
-------------------------------------------------------------------------------REMOVE FROM NOTE -------------------------------------------------------------------------------lockwire nut (140) DPM harness receptacle (150) bracket (160) (detail G)
DPM harness clips (100) and (120) at the 8 o'clock on brackets (110) and position on flanges
(130) C and D (detail E and F)
bolt (70) at the 8 o'clock clamp (80) brackets (90) position on flange D (detail D)
bolt (40) at the 8:30 o'clock clamp (50) brackets (60) position on flange D (detail C)
F 『 EEFF : ALL E Page 40979-21-30
E E Nov 01/02 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E -------------------------------------------------------------------------------REMOVE FROM NOTE -------------------------------------------------------------------------------
R Removal/Installation of the DPM Harness Figure 403/TASK 79-21-30-991-302- 13 (SHEET 1)
F EEFF : E E ECES ALL 『E 79-21-30EEE Page 410 Nov 01/02
R Removal/Installation of the DPM Harness Figure 403/TASK 79-21-30-991-302- 23 (SHEET 2)
F EEFF : E E ECES ALL 『E 79-21-30EEE Page 411 Nov 01/02
R Removal/Installation of the DPM Harness Figure 403/TASK 79-21-30-991-302- 33 (SHEET 3)
F EEFF : E E ECES ALL 『E 79-21-30EEE Page 412 Nov 01/02
F 『
E C F M E
E E
E 56-5B E
E E
bolt (10) at the 9 o'clock clamp (20) brackets (30) position on flange
(3) Put blanking caps and blanking plugs on the connectors and the receptacles.
F 『 EEFF : ALL E Page 41379-21-30
E E Nov 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(52)
