2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform
No specific blanking plug
No specific circuit breaker(s) safety clip(s)
No specific warning notice
98D36003000000 1 TEST SET - ENGINE BLEED SYSTEM
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
31-60-00-860-001 EIS Start Procedure
31-60-00-860-002 EIS Stop Procedure
R 49-00-00-860-003 APU Start by External Power (GTCP 36-300)
R 49-00-00-860-004 APU Shutdown by External Power (GTCP 36-300) 49-00-00-860-005 APU Start by External Power (APS 3200) 49-00-00-860-006 APU Shutdown by External Power (APS 3200) 49-00-00-860-008 APU Start by External Power (131-9(A)) 49-00-00-860-009 APU Shutdown by External Power (131-9(A)) 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
78-30-00-081-041 Make the Thrust Reverser Serviceable after Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors
3. Job Set-up
__________
Subtask 36-11-52-861-064
A. Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
Subtask 36-11-52-941-070
B. Safety Precautions
(1)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(2)
On the ENG panel 115VU:
-put a warning notice to tell persons not to start the engine 1(2).
(3)
On the HP ground connector:
-put a warning notice to tell persons not to pressurize the pneumatic system.
(4)
On the ENG section of the maintenance panel 50VU:
-make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
-put a warning notice to tell persons not to energize the FADEC 1(2).
1EFF : ALL 1 36-11-52Page 509 1 1 Aug 01/04R 1 1 1CES 1
Subtask 36-11-52-860-072
C. Aircraft Maintenance Configuration
(1)
Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. TASK 31-60-00-860-001).
(2)
On the AIR COND panel 30VU:
-
make sure that the PACK 1 and PACK 2 pushbutton switches are released (OFF legends are on),
-
make sure that the X BLEED selector switch is set to OPEN,
-
make sure that the ENG 1 BLEED and ENG 2 BLEED pushbutton switches are pushed (the OFF legends are off).
Subtask 36-11-52-865-071
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/ENG 1/CTL 3HA1 D12 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23
Subtask 36-11-52-010-085-A
E. Get Access
(1)
Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2)
Put an access platform in position at the bleed pressure regulator valve.
Subtask 36-11-52-040-084
F. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
1EFF : ALL 1 36-11-52Page 510 1 1 Aug 01/04R 1 1 1CES 1
Subtask 36-11-52-010-111
G. Open the thrust reverser doors (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 36-11-52-480-058
H. Preparation for the Leak Test
(1) Remove the blanking plug from the test port of the bleed pressure regulator valve.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 2(24)
