(8)
Install the cable (44) in the electrical raceway, in route 2S.
(9)
Install the clamps (33) on the cable (40) and/or the cable (44).
(10)
Install the bolts (35) and if applicable the spacers (43).
(11)
Install the sleeves (28) on the cable (40) and/or the cable (44) and install the cable-ties (42) and the spacers (41).
Subtask 36-22-16-865-060
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2HA1, 3HA1, 2HA2, 3HA2.
Subtask 36-22-16-710-051
D. Test
(1) Do an operational test of the overheat detection system (Ref. TASK 36-22-00-710-001).
5. Close-up
________ Subtask 36-22-16-410-051
A. Close Access
(1) Install the applicable access panels:
-
FOR 21HF, 77HF install 191EB, 191CT, 191BT, 521AB, 521BB, 521CB
-
FOR 37HF, 64HF install 192EB, 192CT, 192BT, 621AB, 621BB, 621CB
Subtask 36-22-16-865-061
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 36-22-16-860-066
C. Aircraft Configuration
(1) Retract the slats fully (Ref. TASK 27-80-00-866-005).
1EFF : ALL 1 36-22-16Page 429 1 1 May 01/05R 1 1 1CES 1
Subtask 36-22-16-942-051
D. Removal of Equipment
(1)
Remove the Safety Barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 36-22-16Page 430 1 1 May 01/05R 1 1 1CES 1
TASK 36-22-16-000-003
Removal of the Cables 24HF(40HF),51HF(67HF)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
1. Reason for the Job__________________
R R Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific No specific 98D27803000000 blanking capscircuit breaker(s) safety clip(s)safety barrierswarning noticeaccess platform 2.8 m (9 ft. 2 in.)1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R 27-80-00-866-004 36-22-16-991-001 36-22-16-991-002 36-22-16-991-004 36-22-16-991-005 Extending the Slats on the GroundFig. 401Fig. 402 Fig. 404 Fig. 405
3. Job Set-up
__________
(Ref. Fig. 401/TASK 36-22-16-991-001, 402/TASK 36-22-16-991-002) Subtask 36-22-16-941-052
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position in the cockpit to tell persons not to operate the slat controls.
Subtask 36-22-16-860-059
B. Aircraft Maintenance Configuration
(1)
Extend the slats fully (Ref. TASK 27-80-00-866-004).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever on panel 114VU.
Subtask 36-22-16-865-052
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11
121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22
1EFF : ALL 1 36-22-16Page 432 1 1 May 01/05R 1 1 1CES 1
Subtask 36-22-16-010-052
D. Get Access
(1)
Put the access platform in position below the applicable access panel.
(2) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 2(123)
