-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-11-49-400-002 Installation of the Hydraulic Pressure Hose/Tube
 Assembly 29-11-49-400-003 Installation of the Top Case Drain Hose/Tube Assembly 29-11-49-400-004 Installation of the Lower Case Drain Hose/Tube
 Assembly 29-11-49-400-005 Installation of the Hydraulic Low-Pressure Switch
 Tube R 29-11-49-400-006 Installation of the Pressure-Relief Valve Hose/Tube R 29-11-49-991-921 Fig. 601
 FOR FIN 1000EM1
 71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors

 3. Job Set-up
__________
 Subtask 29-11-49-941-084
 A. Safety Precautions
 (1)
 On the center pedestal, on the ENG panel 115VU:

 -put a warning notice to tell persons not to start the engine 1.

 (2)
 Make sure that the engine 1 shutdown occurred not less than 5 minutes before you do this procedure.

 (3)
 On the overhead maintenance panel 50VU:

 -make sure that the ON legend of the ENG/FADEC GND PWR 1 pushbutton switch is off.

 (4)
 Put a warning notice to tell persons not to energize the FADEC 1.

 Subtask 29-11-49-010-085
 B. Get Access
 (1)
 Open the fan-cowl doors:
 FOR 1000EM1

 -437AL, 438AR (Ref. TASK 71-13-00-010-040).

 (2)
 Put the access platform in position at the engine.

 Subtask 29-11-49-865-071
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 1702GK R34
 4. Procedure_________ 
R  (Ref. Fig. 601/TASK 29-11-49-991-921)
 Subtask 29-11-49-210-053
R  A. Do a visual inspection of the Hydraulic Hoses and Tubes that are installed on the engine
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
R  1. Examine the hydraulic suction hose-tube assembly, look for: 
R R R  A. Cracks.  None permitted.  Replace the hose-tube assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001). 
R R R  B. Crimps.  None permitted.  Replace the hose-tube assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001). 
R R R R  C. Internal blockage.  None permitted.  Remove the blockage or replace the hose assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001). 
R R R  D. Leakage.  None permitted.  Replace the hose-tube assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001).

R R  Hydraulic Hoses and Tubes Figure 601/TASK 29-11-49-991-921- 12 (SHEET 1)
 1EFF : 1 1 1CES  ALL  1 111 29-11-49 Page 604 Aug 01/05

R R  Hydraulic Hoses and Tubes Figure 601/TASK 29-11-49-991-921- 22 (SHEET 2)
 1EFF : 1 1 1CES  ALL  1 111 29-11-49 Page 605 Aug 01/05

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
R  E. Nicks and 
R  scratches-tubes 
R  portion of suction 
R  hose-tube 
R  assembly. 
R 
R  F. End-fitting thread 
R  damage. 
R 
R 
R 
R 
R  G. End-fitting 
R  damaged flats. 
R 
R 
R 
R 

Maximum depth cannot be more than 0.0035 in. (0.0889 mm) deep (not more than 10 percent of wall thickness).
Damage is permitted if the threads that are good are not reduced by more than one thread.
Damage is permitted if the damaged end-fittings can keep the correct torque value.
If the damage is more than the allowable limits, replace the hose-tube assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001).
If the damage is more than the allowable limits, replace the hose-tube assembly (Ref. TASK 29-11-49-000-001) and (Ref. TASK 29-11-49-400-001).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓2(116)