(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) FOR FIN 1000EM1 No specific access platform 0.8 m (2 ft. 7 in.)
1EFF : ALL 1 29-11-49Page 451 1 1 Aug 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic
Service Cart 29-11-00-710-001 Operational Test of the Green Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-23-00-864-001 Depressurize the Green and Yellow Hydraulic Systems
after Operation of the PTU
29-11-49-991-910 Fig. 407
R 29-11-49-991-922 Fig. 408 FOR FIN 1000EM1 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors
3. Job Set-up
__________
Subtask 29-11-49-860-074
A. Aircraft Maintenance Configuration
(1)
Make sure that the Green hydraulic system is depressurized (Ref. TASK 29-23-00-864-001).
(2)
Make sure that the Green hydraulic reservoir is depressurized (Ref. TASK 29-14-00-614-001).
(3)
Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Green hydraulic system: - on the ground service panel 197CB.
(4)
Make sure that the warning notice(s) is (are) in position on the access door 195BB to tell persons not to pressurize the Green hydraulic reservoir.
Subtask 29-11-49-941-072
B. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
-make sure that the warning notice(s) is (are) in position to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Green hydraulic system:
-in the cockpit, on the HYD section of the overhead panel 40VU.
(4)
On the overhead maintenance panel 50VU:
-make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(5)
Make sure that the warning notice(s) is (are) in position to tell persons not to energize the FADEC 1(2).
(6)
Make sure that a container is below the hydraulic low-pressure switch tube.
Subtask 29-11-49-010-072
C. Get Access
(1)
Make sure that the left fan cowl door is open:
FOR 1000EM1
-make sure that the door 437AL is open (Ref. TASK 71-13-00-010-040).
(2)
Make sure that the access platform is in position at the engine.
4. Procedure
_________
R
Subtask 29-11-49-420-065
A. Installation of the Hydraulic Low-Pressure Switch Tube R (Ref. Fig. 407/TASK 29-11-49-991-910) R PRE SB RA32029-13
(1)
Remove the protective covers from the hydraulic low-pressure switch tube (15), the fitting on the pressure hose/tube and the hydraulic low-pressure switch.
(2)
Loosely connect the low-pressure switch tube (15) to the pressure hose/tube.
(3)
Loosely connect the low-pressure switch tube (15) to the hydraulic low-pressure switch.
(4) Install the clamp (20) on the low-pressure switch tube (15). Attach
the two tubes to the channel with the bolt (5), the washer (10) and
the clamps (20).
(5) Make sure that the low-pressure switch tube (15) is in the correct
position on the engine.
NOTE : Use a second wrench to hold the fittings when you TORQUE the____
coupling nuts. This prevents damage to the tube assemblies.
(6) TORQUE the coupling nut on the low-pressure switch (15) to between 7
and 7.68 m.daN (51.62 and 56.63 lbf.ft).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM HYDRAULIC POWER 液壓2(108)
