(2)
FOR 28QM, 30QM
put the bracket (2) in position on RIB15.
(3)
Install the bolts (1).
(4)
Make sure that the splines on the transfer valve (5), are fully engaged with the splines on the transfer valve drive (6).
(5)
Apply SEALANTS (Material No. 09-007) over the ends of the bolts.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-15-41Page 411 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Post SB 28-1077 For A/C 001-001,051-052,
Subtask 28-15-41-420-050-A
B. Installation of the Transfer Valve
R (1) FOR 27QM, 29QM do the steps that follow:
(a)
Push the transfer valve (5) into the transfer valve drive (6). Install the transfer valve (5) on RIB15 and hold it in position.
(b)
Install the bolts (1). NOTE : You must bond one of the bolts (1) (Ref. TASK 28-15-41-
____ 991-001) (Ref. TASK 20-28-00-912-002).
(c)
Make sure that the splines on the transfer valve (5), are fully engaged with the splines on the transfer valve drive (6).
(d)
Apply SEALANTS (Material No. 09-007) over the ends of the bolts.
R (2) FOR 28QM, 30QM do the steps that follow:
(a)
Push the transfer valve (5) into the transfer valve drive (6). Install the transfer valve (5) on RIB15 and hold it in position.
(b)
Put the bracket (2) in position on RIB15. NOTE : Bond the bracket (2) using the Direct Contact Method
____ (Ref. TASK 20-28-00-912-043).
(c)
Install the bolts (1). NOTE : You must bond one of the bolts (1) (Ref. TASK 28-15-41-
____ 991-001) (Ref. TASK 20-28-00-912-002).
(d)
Make sure that the splines on the transfer valve (5), are fully engaged with the splines on the transfer valve drive (6).
(e)
Apply SEALANTS (Material No. 09-007) over the ends of the bolts.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-15-41Page 412 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-15-41-410-052
C. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. TASK 28-10-00-910-002), (Ref. TASK 57-27-11-400-002):
-
FOR 27QM, 28QM
install 540JB, 540KB
-
FOR 29QM, 30QM
install 640JB, 640KB.
Subtask 28-15-41-865-052
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1QP, 2QP, 3QP, 4QP.
5. Close-up
________
Subtask 28-15-41-710-050
A. Operational Test
(1) Do an operational test of the transfer valve (Ref. TASK 28-15-00-710-002).
Subtask 28-15-41-650-051
B. Fuel Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-15-41Page 413 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 28-15-41-942-051
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-15-41Page 414 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 SHAFT - DRIVE, TRANSFER VALVE (70QM,71QM,72QM,73QM) - REMOVAL/INSTALLATION
__________________________________________________________________________
TASK 28-15-42-000-001
Removal of the Transfer Valve Drive 70QM(72QM)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油2(66)
