-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------When the loading is completed:
-The two MCDUs go back to the A/C status page with the CROSSLOAD COMPLETED indication in the scratchpad.
3. On the MCDUs 1 and 2:
-Push the line key adjacent to The DATA INDEX page comes into view. the RETURN indication.
-On the line key adjacent to the Compare the two MCDUs:
A/C STATUS indication. - Make sure that the dates and the data base numbers of the ACTIVE DATA BASE are the same
-Make sure that the ACTIVATE CROSSLOAD indication does not come into view.
R **ON A/C 106-149, 151-199, 211-299, 301-399, 401-499,
Post SB 22-1089 For A/C 151-199,211-212,
Subtask 22-70-00-970-071-A
A. Procedure of the Crossloading of the FMGC Data Base
NOTE : When you do the crossloading procedure:
____
-
Of one element that you can load (e.g. Navigation Data Base), use the related P/N STATUS page (e.g. page No.3 for the crossloading of the Navigation Data Base) on the MCDU1 to load the FM2, or on the MCDU2 to load the FM1.
-
Of the total elements that you can load, use the P/N XLOAD page No. 1 on the MCDU1 to load the FM2 (FMS2 UPDATE indication), or on the MCDU2 to load the FM1 (FM1 UPDATE indication). Only the different elements are crossloaded.
NOTE : On the MCDU 1 and 2, the INDEPENDENT OPERATION indications are
____ shown in the scratchpad. Use the MCDU related to the side from which you will do the crossloading.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On this MCDU:
-Make sure that the FMS1 and the FMS2 have different P/Ns
-
Push the line key adjacent to the START XLOAD indication
-
Push the line key adjacent to the CONFIRM indication.
2. When the loading is completed, for the loaded FMGC:
-Open the circuit breaker 10CA1 for the FMGC1, or 10CA2 for the FMGC2, for more than 5 seconds.
3.
Close the applicable circuit breaker 10CA1 or 10CA2.
4.
When the safety test of this FMGC is completed, on the MCDU 1 and 2, make sure that:
-The INDEPENDENT OPERATION indications are not shown in the scratchpad.
On this MCDU:
-
The ACCEPTING XLOAD indication comesinto view
-
The XLOAD IN PROCESS indication andthe REMAINING time indication come into view together.
Subtask 22-70-00-280-073
B. Do a check of the reference of the software loaded in the FMGC, on the MCDU:
(1) Make sure that the P/N XLOAD 1/6 page is shown on the MCDU:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU: On the MCDU:
-Get the page related to the - Make sure that the reference (P/N) loaded element (use the line shown is the same as the reference on select key adjacent to the NEXT the disk(s). PAGE or PREV PAGE indication).
R **ON A/C 051-099, 106-149, 151-199, 201-299, 301-399, 401-499,
5. Close-up
________
**ON A/C 051-099, 151-199, 201-212,
Subtask 22-70-00-860-116
A. Put the aircraft back to its initial configuration.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM AUTO FLIGHT 自動飛行3(9)
