曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  - connect the connecting cable to 
R  the SYST1(2) connector. 
R  5. Close the circuit breaker 11CA1 
R  (11CA2). 
R  6. On the carry-on loader: 
R  - cet the ON/OFF switch to ON. 
R  7. Put the floppy disk into the 
R  loader. 
R  8. Close the circuit breaker 10CA1 
R  (10CA2). 
R 
R 
R 
R 
R 
R 
R 
R 
R 
R  9. On the carry-on loader: 
R  - eject the floppy disk. 
R  - set the ON/OFF switch to OFF. 
R  10. Open the circuit breakers 10CA1 
R  (10CA2) and 11CA1 (11CA2). 
R  11. On the panel 52VU: 
R  - disconnect the carry on loader 
R  connecting cable 
R  - install the FMS LOAD blanking 
R  plate. 
R  12. Close the circuit breakers 
R  10CA1, 10CA2, 11CA1, 11CA2 and 
R  wait 1 minute. 
R  13. On the center pedestal, on the 
R  MCDU1(2):

On the carry-on loader:
-all lights flash, then go off.
-
the RDY indicator light comes on.

-
the power-up test of the FMGC1(2) starts.

-at the end of this test, the triple click aural warning sounds. On the carry-on loader the PROG indicator light comes on.
-When all the data are put into the computer (a time duration of 25 minutes can be necessary), the RDY and PROG indicator lights go off and the COMP indicator light comes on.
1EFF : 062-099, 1 22-70-00Page 341 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION  RESULT
 -------------------------------------------------------------------------------
R  - push the MCDU MENU mode key.  The MCDU MENU page comes into view. 
R  - push the line key adjacent to  An FM page comes into view. 
R  the FMGC indication. 
R  - push the DATA mode key.  The DATA INDEX page comes into view. 
R  - push the line key adjacent to  The A/C STATUS page comes into view. 
R  the A/C STATUS indication. 
R  Subtask 22-70-00-710-063 
R  B. On the center pedestal, on the A/C STATUS page of the MCDU1(2) do a check 
R  of: 
R  - the active data base of the FMGC, in which you put the data, for 
R  correct dates and serial numbers shown (it is necessary to open the 
R  circuit breaker of the opposite FMGC). 
R  5. Close-up________ 
R  Subtask 22-70-00-862-080 
R  A. De-energize the aircraft electrical circuits 
R  (Ref. TASK 24-41-00-862-002).

 1EFF : 062-099, 1 22-70-00Page 342 1 1 May 01/05 1 1 1CES 1

 

R **ON A/C 051-099, 106-149, 151-199, 201-299, 301-399, 401-499,

 TASK 22-70-00-610-009 Crossload the FM Data WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______ YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
 1.
 Reason for the Job

__________________
 Crossload the FM Data of one FMGC into the other one.

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002  Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power
 3. Job Set-up
__________ Subtask 22-70-00-860-115
 A. Aircraft Maintenance Configuration
 (1)
 Energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-861-002).

 (2)
 Make sure that the aircraft is in the ground configuration.

 (3)
 On the MCDUs 1 and 2, set the BRT knob to the middle position.

 

 4. Procedure
_________

 **ON A/C 051-099, 151-199, 201-212,
 Subtask 22-70-00-970-071
 A. Procedure of the Crossloading of the FMGC Data Base
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDUs 1 and 2:
 - Push the MCDU MENU mode key.  The MCDU MENU page comes into view.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AUTO FLIGHT 自動飛行3(8)