EFFECTIVITY
AT 701-750
799 Page 404
34-41-07
Oct 25/80
B556
R304
R288
R306
R302
R297
R449
B231
R855
R856
R450
R298
R303
R307
B557
R289
R305
NOTE: WIRING AND CONNECTOR DETAIL OMITTED FOR CLARITY.
P73 FLIGHT INSTRUMENT SWITCHING RELAY PANEL
R288
R289
R297 R298 R302 R303 R304 R305 R306 R307 R449 R450 R855 R856 B231 B556 B557
FLIGHT DIRECTOR COMPUTER SELECT
RELAY NO. 1 (CAPT)
FLIGHT DIRECTOR COMPUTER SELECT
RELAY NO. 2 (F/O)
RADIO/INS RELAY NO. 1 (CAPT)
RADIO/INS RELAY NO. 2 (F/O)
INS TRANSFER RELAY NO. 1 (CAPT)
INS TRANSFER RELAY NO. 2 (F/O)
ATTITUDE TRANSFER RELAY NO. 1 (CAPT)
ATTITUDE TRANSFER RELAY NO. 2 (F/O)
COMPASS TRANSFER RELAY NO. 1 (CAPT)
COMPASS TRANSFER RELAY NO. 2 (F/O)
VOR/ILS TRANSFER A RELAY NO. 1 (CAPT)
VOR/ILS TRANSFER A RELAY NO. 2 (F/O)
VOR/ILS TRANSFER B RELAY NO. 1 (CAPT)
VOR/ILS TRANSFER B RELAY NO. 2 (F/O)
INSTRUMENT SWITCHING ACCESSORY BOX
BUFFER AMPLIFIERS (CAPT)
BUFFER AMPLIFIERS (F/O)
Flight Instrument Switching Relay Panel Figure 401 (Sheet 4)
EFFECTIVITY
SN ALL EXCEPT 301,302
799 Page 405
34-41-07
Apr 25/86
INS BATTERY TRANSFER RELAY - REMOVAL/INSTALLATION
_________________________________________________
1. General
_______
A. The INS battery transfer relay is located in covered panel P123 on the forward side of bulkhead 400 in the right nose wheel well crawlway (access through the main electronic equipment center).
B. During relay removal or installation, the INS BAT PARALLEL switch (flight engineer's panel, P4) must be in the NORMAL position and the mode select switch (pilots' overhead panel, P5) for INS 1 and 3 must be in the OFF position. Prior to removal, open circuit breaker on front panel of INS batteries 1 and 3 and close after installation.
C. After installation test per transfer relay operational test. (Refer to 34-41-11, INS Battery Transfer Relay - Adjustment/Test.)
EFFECTIVITY
ALL 03 Page 401 Oct 10/7334-41-11
INS BATTERY TRANSFER RELAY - ADJUSTMENT/TEST
____________________________________________
1. INS Battery Transfer Relay Test
_______________________________
A. Referenced Procedures
(1)
24-22-00, Manual Control - Maintenance Practices (Apply Power)
(2)
21-58-00, Equipment Cooling - Adjustment/Test (Operating Test)
(3)
24-33-00, DC Standby Power System - Description and Operation (Control)
B. Prepare for Test
(1)
On mode selector units for INS 1 and INS 3 (pilots' overhead panel P5), place mode selector switch in OFF position.
(2)
Set STANDBY POWER switch (on flight engineer's P4 panel) to MANUAL ON position.
(3)
On flight engineer's panel P4, set INS BAT PARALLEL switch to NORMAL position.
(4)
Apply aircraft power (Ref 24-22-00).
(5)
Supply equipment cooling (Ref 21-58-00).
CAUTION: ENSURE THAT COOLING AIR IS AVAILABLE TO NAVIGATION
_______ UNITS BEFORE OPERATING INS. FAILURE TO PROVIDE ADEQUATE AIR SUPPLY WILL RESULT IN FAILURE OF NAVIGATION UNITS.
(6)
Ensure inertial navigation systems 1 and 3 have battery, navigation, control/display and mode selector units properly installed.
(7)
Close both pair of power circuit breakers (PWR-INS 1 for system 1, PWR-INS 3 for system 3) on electronic circuit breaker panel P7 (or P126).
(8)
On airplanes with PMS, when the INS is in the PMS waypoint control mode; control of the INS is through the PMS CDU, and the INS CDU operates only as a display unit. To operate the INS totally independent of the PMS, open the PMS circuit breakers (Ref 34-62).
(9)
On ATLAS ALL EXCEPT AT 701-750, set ATT/COMP STAB switch on the captain's main instrument panel to CAPT 1 - F/O 2 position. On AT 701-750, set ATTITUDE switch on captain's main instrument panel to NORM.
(10)
Close circuit breaker on front panel of INS battery units 1 and 3.
C. Test Battery Transfer Relay
(1) Turn on check and lamp test (AIRPLANES WITH DELCO INS)
(a) Set mode selector switches on mode selector units 1 and 3 to STBY position. Check that on CDU 1 and 3 and MSU 1 and 3: 1) Red, amber and green lamps do not illuminate.
NOTE: Some lights, including the red WARN light and green
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航3(74)
