(3)  
Message slot 3 - Range message located at top right displays
 selected range in blue.

 (4)  
Message slot 4 - Color bar located directly below the mode message is displayed. This message slot normally displays a green, yellow, and red color bar. If the display experiences a color scheme failure, the message slot will identify the modified color scheme. When the slave operation is selected a SLV message will replace the three color bar display. If a system failure occurs a failure message identifing the faulty LRU will be displayed in place of the color bar or the SLV message. The LRU failure message will be displayed as T/R (receiver-transmitter), ANT (antenna), CTL (control panel), or DSP (indicator) in yellow.

 (5)  
Message slot 6 - Ground clutter suppression message located at bottom left of indicator displays IDNT when ground clutter suppression is selected. Normally the slot is blank.

 EFFECTIVITY

 AF 160, 162-171, 183, 184  CONFIG 4  01 Page 102  Sep 25/9434-43-00
 (6)  
Message slot 7 - Stabilization status message located at bottom right center. For stabilized operation, if the INS provides proper inputs, this slot will be blank. A flashing ATT will be displayed when an attitude input failure is detected (INS OFF or providing invalid pitch or roll signals). SAT will be displayed when system stabilization limits are exceeded due to unusual attitude maneuvers. All messages are blue color.

 (7)  
Message slot 8 - Antenna tilt located in bottom right corner of the indicators. Message displays the antenna tilt angle in 0.25-degree increments in blue (cyan), from 15.00(X) to 15.00(X) where (X) represents an arrow pointing upward or downwards depending on the direction of antenna tilt selected. If the antenna tilt position is different than the position annunciated, a flashing FAIL message is displayed in slot 2 and an ANT message in slot 4).

 (8)  
Message slot 9 - System message located below message slot 3 (range) this message displays which system is selected. This slot will be blank when system 1 is selected and will display S2 when system 2 is selected.

 E.  If any of the following switches and controls are malfunctioning replace the indicator.
 (1)  
MKR intensity control

 (2)  
INT display intensity control

 (3)  
M/S master slave switch

 (4)  
AF 160, 162-171;
 AZ azimuth marker switch

 (5)  
AF 160, 162-171;
 HOLD switch

 (6)  
LFT, FWD or RGT display switches

 (7)  
Range switches

 F.  When TEST mode is selected, entire system is energized. Receive-transmit circuits are tested (system transmits) for one second and then are muted. A tilt and scan test is performed for the next 15 seconds ending electronically locked in boresight position and a test pattern of four concentric colored arcs appears on indicator (Fig. 101).
 G.  R/T front panel contains an elapsed time counter, OVERTEMP indicator, and overtemp RESET switch.
 NOTE: Some R/Ts will not be equipped with an OVERTEMP indicator or
____
 overtemp RESET switch.

 (1)  
Elapsed time counter indicates number of hours of operation.

 (2)  
OVERTEMP indicator annunciates if power supply temperature exceeds minimum cooling requirements.

 (3)  
Overtemp RESET switch allows overtemp indicator to be reset to no-fault position.

 2.  Prepare for Trouble Shooting
____________________________
 A.  Check that WEA RDR R/T 1, R/T 2, IND 1, IND 2, and that CAPT and F/O FLT INST SW RELAYS ATTD/ CMPS STAB circuit breakers on electronics circuit breaker panel P7 are not flagged with Do-Not-Operate identifiers.
 EFFECTIVITY

 AF 160, 162-171, 183, 184  CONFIG 4  01 Page 103  Sep 25/9434-43-00
 B. Observe following precaution when operating weather radar system.

 WARNING: DO NOT OPERATE WEATHER RADAR WHILE AIRPLANE IS BEING REFUELED
_______ AND DO NOT OPERATE IN ANY RADIATING MODE WHILE A FUELING OPERATION IS BEING CONDUCTED WITH 300 FEET OF ANTENNA OR AN EXPLOSION MAY OCCUR.
 PERSONNEL MUST NOT ENTER AN AREA CLOSER THAN 50 FEET IN FRONT OF A RADIATING ANTENNA OR INJURY TO PERSONNEL MAY OCCUR.
 C.  Provide electrical power (Ref 24-22-00).
 D.  Provide cooling air to electronic equipment (Ref 21-58-00).
 CAUTION: ENSURING EQUIPMENT COOLING IS OPERATED BEFORE TURN ON OF
_______ ELECTRONIC SYSTEMS OR DAMAGE TO EQUIPMENT MAY RESULT. EQUIPMENT COOLING SYSTEM MUST BE SET FOR NORMAL COOLING AS DESCRIBED IN 21-58-00.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航3(123)