曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 B.  Replacement of a magnetic field sensor will not normally degrade MHRS performance unless field sensor or mounting bracket alignment is changed.
 2.  Referenced Procedures_____________________
 A.  34-21-01, Adjustment/Test
 3.  Remove Field Sensor___________________
 CAUTION: USE NONMAGNETIC TOOLS AND MOUNTING HARDWARE WHEN WORKING ON THE
_______ FIELD SENSOR OR COMPASS SYSTEM CALIBRATION MAY BE DISTURBED.
 DO NOT LOOSEN FIELD SENSOR INDEXING SCREWS OR REINDEXING (A BENCH ADJUSTMENT) WILL BE REQUIRED.
 DO NOT LOOSEN MOUNTING BRACKET INDEXING SCREWS OR SYSTEM REFERENCE TO AIRPLANE CENTERLINE WILL BE LOST.
 DO NOT MEASURE FIELD SENSOR CONTINUITY WITH AN OHMMETER. CURRENT FLOW THROUGH SENSING COILS MIGHT DAMAGE UNIT.
 A.  Open MHRS 1 and MHRS 2 circuit breakers on electronic circuit breaker panel (P7).
 B.  Gain access to field sensor, disconnect electrical connector, and remove nonmagnetic mounting screws.
 4.  Install Field Sensor____________________
 A.  Open MHRS 1 and MHRS 2 circuit breakers on electronic circuit breaker panel (P7).
 B.  Install field sensor with mounting screws, connect electrical connector, and replace access cover.
 C.  Close MHRS 1 and MHRS 2 circuit breakers (panel P7).
 D.  Test field sensor (Ref 34-21-01).
 EFFECTIVITY

 

 ALL  03 Page 401  Apr 25/8734-21-01
SEE A
FIELD SENSOR 
INDEXING SCREW (3) 
(DO NOT REMOVE)  ELECTRICAL 
CONNECTOR 
MOUNTING BRACKET 
INDEXING SCREW 
(DO NOT REMOVE) 
MOUNTING 
SCREW 
(4 PLACES) 

A

Magnetic Field Sensor Installation
Figure 401

EFFECTIVITY

ALL 701 Page 402
34-21-01

Oct 10/73
 606354
 MAGNETIC FIELD SENSOR - ADJUSTMENT/TEST
_______________________________________

 1. Magnetic Field Sensor Test
__________________________
 A. Referenced Procedures
 (1)  
21-58-00, Adjustment/Test (Operational Test)

 (2)  
24-22-00, Maintenance Practices (Apply Power)

 (3)  
34-21-00, Adjustment/Test (Operational Test)

 (4)  
34-41-00, Adjustment/Test (Operational Test)

 B. Prepare for Test
 (1)  
Provide electrical power (Ref 24-22-00).

 (2)  
Supply equipment cooling to main equipment center shelves (Ref 21-58-00).

 CAUTION: IF OPERATED WITHOUT PROPER COOLING, DAMAGE TO ELECTRONIC
_______
 EQUIPMENT COULD RESULT.

 (3)  
Turn on inertial navigation systems No. 1 and No. 2. Ensure that they are operating in NAV mode with present position inserted. Main power, platform heading and HSI circuit breakers must be closed (Ref 34-41-00).

 (4)  
Set both VOR/ILS-INS switches to VOR/ILS.

 (5)  
On ALL EXCEPT AT ALL,
 set captain's COMPASS switch to CAPT 1-F/O2.
 On AT ALL,
 set captain's COMPASS switch to NORM.

 (6)  
On ALL EXCEPT AT ALL, set captain's ATT/COMP STAB switch to CAPT 1-F/O 2. On AT ALL, set captain's ATTITUDE switch to NORM.

 C. Test Magnetic Field Sensor
 (1)  
Close circuit breakers for magnetic heading reference systems No. 1 and No. 2 (Ref 34-21-00).

 (2)  
Set compass controller switches for MHRS No. 1 and No. 2 to SLAVED.

 (3)  
Allow systems to stabilize for approximately 5 minutes.

 (4)  
Observe that heading flags are out of view and all compass cards indicate present airplane magnetic heading in captain's and first officer's horizontal situation and radio magnetic indicators.

 (5)  
On both compass controllers, observe that synchronization annunciator is centered.

 (6)  
Turn off inertial navigation systems if no longer required (Ref 34-41-00).

 (7)  
Remove equipment cooling if no longer required (Ref 21-58-00).

 (8)  
Remove electrical power if no longer required (Ref 24-22-00).

 EFFECTIVITY

 

 ALL  26 Page 501  Oct 25/8034-21-01
 MAGNETIC COMPENSATOR - REMOVAL/INSTALLATION
___________________________________________

 1.  General
_______
 A.  The magnetic compensator is installed on shelf El-1 in the main equipment center. Each unit is held in place by two quick-release fasteners and has one electrical cable attached to the rear panel through a connector.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航1(135)