(3)  
Verify application of air by observing that the duct pressure indicator on the flight engineer's panel registers approximately 40 PSI.

 EFFECTIVITY
 AT ALL; MD ALL; VM ALL;  CONFIG 2 IB 406-499  09 Page 503  Apr 25/86

34-15-00
 (4)  Verify air flow from left TAT probe.  Air should exit probe at a
 rate of approximately two cubic feet per minute.
 (5)  Place a thermometer adjacent to left TAT probe.  Shield from
 direct sunlight, wind, probe windstreams and contact with probe
 or airplane.
 (6)  Condition the left TAT probe such that the TAT/EPRL indicator TAT
 readout is +45.C or less.
 NOTE:____ Heat may be applied probe by holding LEFT probe heater
 switch on pilots' overhead panel in TAT TEST position.
 (7)  After thermometer has stabilized, check that TAT indication agrees
 with ambient temperature of probe within | 2.0.C.  Remove
 thermometer.
 (8)  Select each of the flight modes in any sequence on mode selector
 panel.  Check that mode selected is displayed by indicator and TAT
 indication should not be affected by switching from any one mode to
 another.
 (9)  Simulate a .211 mach input per applicable section of the central
 air data computer - adjustment/test, 34-12-00.

 (10) Select TOD mode on mode selector panel.  Apply heat to left TAT probe to verify that TAT indication increases to 59.C or more. Check that EPRL readout decreases as TAT readout increases over the range +45.C through +55.C. At 59. -0. +4.C, the yellow warning flags should obscure the TAT and EPR limit readouts. Remove heat and verify that TAT flap disappears from view at or before a temperature of 59.C is reached and that EPR limit flag disappears from view at or above a TAT indication of 52.C.
 NOTE: Set LEFT probe heater switch to OFF when yellow warning
____ flags appear or at a TAT readout of +63.C maximum.
 (11)
 Remove mach input.

 (12)
 Lower nacelle anti-ice module from overhead panel P5.

 (13)
 Select CON flight mode on mode selector panel and observe EPRL counter readout on TAT/EPRL indicator.

 (14)
 Apply a jumper cable between terminal 2 of No. 1 nacelle anti-ice valve open light and aircraft ground. Observe that EPRL reading on TAT/EPRL indicator decreases an appreciable amount.

 (15)
 Place wing anti-ice.  Switch on pilots' overhead panel to ON. EPRL reduction should be approximately double of previous test.

 (16)
 Set wing anti-ice switch to OFF and remove jumper cable from No. 1 nacelle anti-ice valve open light. Observe that EPRL counter readout returns to original value.

 (17)
 Repeat above procedure for nacelle anti-ice valve lights 2, 3 and

 4. In each case, indicator readout reduction should be approximately the same value as above.

 (18)
 Remove jumper cable, place wing anti-ice switch to OFF and install nacelle anti-ice module.

 (19)
 Shutdown air supply to aspirated temperature probe.

 (20)
 Remove electrical power if no longer required (Ref 24-22-00).

 EFFECTIVITY
 AT ALL; MD ALL; VM ALL;  CONFIG 2 IB 406-499  09 Page 504  Apr 25/86

34-15-00
 ALTITUDE ALERT SYSTEM - DESCRIPTION AND OPERATION
_________________________________________________

 1. General_______(Fig. 1)

 A.  The Altitude Alert System (AAS) provides aural and visual signals to the pilots when the airplane approaches or deviates from a selected altitude. Selected altitude is set by the ALT SEL control on the autopilot-flight director mode select panel.
 B.  The altitude alert system includes an altitude alert computer, an altitude alert test switch, an altitude select panel, and two altitude alert annunciators.
 C.  The altitude alert computer receives 28-volt dc power from flight instrument bus No. 2, and 26-volt ac power from flight instrument bus No. 2 autotransformer No. 6.
 D.  The altitude alert computer receives altitude data from central air data computer No. 2, altitude select data from the autopilot-flight director mode select panel, barometric pressure correction from the first officer's altimeter barometric setting, and an inhibit deviation signal from the main landing gear DOWN sensor.
 E.  The captain's and first officer's altitude alert annunciators illuminate when approaching the selected altitude in either ascent or descent.
 F.  All XA except AF 121, 122, 157, 161, 183, 184; The altitude alert computer automatically resets to the approach mode whenever the difference between the selected altitude and the actual altitude exceeds 950 feet because of airplane altitude change or new altitude selection on ALT SEL control.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航1(111)