曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(1) Disconnect the airplane battery. Refer to Chapter 24-31
(2) Remove the instrument panel cover. Refer to Chapter 25-10
(3) Disconnect the two electrical connectors
from the rear of the oil pressure indicator.
(4) Remove the locking ring from the oil
pressure indicator.
Hold the oil pressure indicator while you
remove the locking ring.
(5) Remove the oil pressure indicator from the
instrument panel into the cockpit.
B. Install The Oil Pressure Indicator
Detail Steps/Work Items Key Items
(1) Position the oil pressure indicator into the
instrument panel from the cockpit.
(2) Install the oil pressure indicator:
− Put the locking ring onto the oil pressure
indicator.
− Turn the locking ring clockwise until the
oil pressure indicator is tight in position.
Make sure the oil pressure indicator is
positioned correctly before you attach the
locking ring.
(3) Connect the two electrical connectors to the
oil pressure indicator.
(4) Install the instrument panel cover. Refer to Chapter 25-10
(5) Do an engine run up test. Look specially for
correct oil pressure indications.
Refer to the Teledyne Continental Motors
Maintenance Manual for oil pressure data.
For the engine run procedures refer to the
DA20-C1 Flight Manual.
Oil Systems
DA20-C1 AMM
Page 210
29 Apr 2004 79-00-00 Doc # DA 201-C1
Rev. 9
9. Remove/Install The Oil Temperature Indicator
A. Remove The Oil Temperature Indicator
Detail Steps/Work Items Key Items
(1) Disconnect the airplane battery. Refer to Chapter 24-31
(2) Remove the instrument panel cover. Refer to Chapter 25-10
(3) Disconnect the two electrical connectors
from the rear of the oil temperature indicator.
(4) Remove the locking ring from the oil
temperature indicator.
Hold the oil temperature indicator while
you remove the locking ring.
(5) Remove the oil temperature indicator from
the instrument panel into the cockpit.
B. Install The Oil Temperature Indicator
Detail Steps/Work Items Key Items
(1) Put the oil temperature indicator into the
instrument panel from the cockpit.
(2) Install the oil temperature indicator:
− Put the locking ring onto the oil
temperature indicator.
− Turn the locking ring clockwise until the
oil temperature indicator is tight in
position.
Make sure the oil temperature indicator is
positioned correctly before you attach the
locking ring.
(3) Connect the two electrical connectors to the
oil temperature indicator.
(4) Install the instrument panel cover. Refer to Chapter 25-10
(5) Do an engine run up test. Look specially for
correct oil temperature indications.
Refer to the Teledyne Continental Motors
Maintenance Manual for oil temperature
data. For the engine run procedures refer
to the DA20-C1 Flight Manual.
DA20-C1 AMM
Oil Systems
Doc # DA 201-C1
Rev. 0 79-00-00 Page 211
19 Dec 1997
10. Remove/Install The Air/Oil Separator
A. Remove The Air/Oil Separator
Detail Steps/Work Items Key Items
(1) Remove the engine cowlings. Refer to Chapter 71-10
WARNING: DO NOT GET OIL ON YOU. OIL CAN CAUSE SKIN DISEASE.
(2) Remove the worm drive clamp from the
rubber hose/vent pipe connection on the top
of the air/oil separator.
(3) Remove the worm drive clamp from the
rubber hose/oil sump connection at the air/oil
separator.
(4) Remove the worm drive clamp from the
rubber hose/breather pipe connection at the
air/oil separator.
(5) Carefully pull the air/oil separator clear of the
rubber hoses. Remove the air/oil separator.
B. Install The Air/Oil Separator
Detail Steps/Work Items Key Items
WARNING: DO NOT GET OIL ON YOU. OIL CAN CAUSE SKIN DISEASE.
(1) Examine the hoses for blockage. Remove any blockage.
(2) Put the air/oil separator in position. Attach
the three hoses.
Make sure you connect the correct hoses
to the inlet, outlet and vent connections on
the air/oil separator.
(3) Install the worm drive clamps to these
connections:
− Vent pipe connection on the top of the
air/oil separator.
− Breather pipe connection at the air/oil
separator.
− Oil sump connection at the air/oil
separator.
(4) Install the engine cowlings. Refer to Chapter 71-10
Oil Systems
DA20-C1 AMM
Page 212
19 Dec 1997 79-00-00 Doc # DA 201-C1
Rev. 0
11. Remove/Install The Oil/Air Separator Vent
A. Remove The Oil/Air Separator Vent
Detail Steps/Work Items Key Items
(1) Remove the engine cowlings. Refer to Chapter 71-10
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石20系列AMM 2(113)