(d)
New engines and propellers must conform to the type design and must be in a condition for safe operation.

(e)
Used engines and propellers which are not being exported as part of a certi.cated aircraft must have been newly overhauled.

(f)
The special requirements of the importing country must have been met.

′
Elodie Roux. Septembre 2003
Subpart L–Export Airworthiness Approvals
(g) Aproduct need not meet a requirement speci.edinparagraphs(a) through(f) of this section, as applicable,if acceptable to theimporting country and theimporting country indicates that acceptability in accordance with Sec. 21.327(e)(4) of this Part.
Amdt. 21-79, E.. 4/27/2001
FAR 21.331 : Issue of airworthiness approval tags for Class II products.
(a)
[An applicantis entitledto an export airworthiness approvaltagforClassIIproducts ifthat applicant shows, except asprovidedinparagraph(b) of this section,that–

(1)
The products are new or have been newly overhauled and conform to the approved design data;

(2)
The products are in a condition for safe operation;

(3)
The products are identi.ed with at least the manufacturer’s name, part num-ber, model designation (when applicable), and serial number or equivalent; and

(4)
The products meet the special requirements of the importing country.

(b)
Aproduct need not meet arequirement speci.edinparagraph(a) ofthis section if acceptable to the importing country and the importing country indicates that acceptability in accordance with Sec. 21.327(e)(4) of this Part.]

Amdt. 21-48, E.. 4/16/79
FAR 21.333 : Issue of export airworthiness approval tags for Class III pro-ducts.
(a)
[An applicant is entitled to an export airworthiness approval tag for Class III pro-ductsifthat applicant shows, except asprovidedinparagraph(b) of this section, that–

(1)
The products conform to the approved design data applicable to the Class I or Class II products of which they are a part;

(2)
The products are in a condition for safe operation; and

(3)
The products comply with the special requirements of the importing country.

(b)
Aproduct need not meet arequirement speci.edinparagraph(a) ofthis section if acceptable to the importing country and the importing country indicates that acceptability in accordance with Sec. 21.327(e)(4) of this Part.]

Amdt. 21-48, E.. 4/16/79
FAR 21.335 : Responsibilities of exporters.
Each exporter receiving an export airworthiness approval for a product shall–
(a) Forwardto the air authorityoftheimporting country alldocuments andinformation necessary for the proper operation of the products being exported, e.g., Flight Manuals, Maintenance Manuals, Service Bulletins, and assembly instructions, and such other material as is stipulated in the special requirements of the importing country.Thedocuments,information, and material maybeforwardedby any means consistent with the special requirements of the importing country;
(b)
Forward the manufacturer’s assembly instructions and an FAA-approved .ight test checko. form to the air authority of the importing country when unassembled aircraft arebeing exported.Theseinstructions mustbein su.cientdetail topermit whatever rigging, alignment, and ground testing is necessary to ensure that the aircraft will conform to the approved con.guration when assembled;

(c)
Remove or cause to be removed any temporary installation incorporated on an air-craft for the purpose of export delivery and restore the aircraft to the approved con.gurationuponcompletionof thedelivery .ight;

(d)
Secure all proper foreign entry clearances from all the countries involved when conducting salesdemonstrationsordelivery .ights; and

(e)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：FAA規章 美國聯邦航空規章 Federal Aviation Regulations 1(108)