S 865-349

 (9)  
Open these circuit breakers on the P11 panel and attach DO-NOT-CLOSE tags:

 (a)  
11B19 or 11A19, STAB TRIM ALT (IF INSTALLED)

 (b)  
11C12, STAB TRIM SHUTOFF LEFT

 (c)  
11C13, STAB TRIM SHUTOFF RIGHT

 (d)  
11H11 or 11C05, STAB TRIM CONT L

 (e)  
11H20, STAB TRIM CONT R

 F.
Control Column Travel Test

 S 215-100
 (1)  Make sure that the left and center hydraulic systems are pressurized
 (AMM 29-11-00/201).
 S 215-101
 (2)  Make sure that Dimension B on the stabilizer ballscrew actuator is
 15.89 | 0.01 inches (403.6 | 0.3 mm) (Fig. 502).
 S 725-005
 (3)  Do the steps that follow to make sure the control column operates
 correctly:
 (a)  Shake the captain's control column forward and aft quickly to
 make sure the control column is at neutral, then release.
 (b)  Use a control surface protractor to make a mark of the column's
 neutral position.
 (c)  Push the captain's control column forward to the column stop.
 (d)  Make sure that the angle from the neutral column position to
 the forward stop is at least 8.90 degrees (Fig. 505).

 NOTE: Approximately a 55-pound (245 newton) push is necessary
____
 to make sure the column touches the stop.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 02 Page 567 ú May 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

(e)

(f)

(g)

(h)

757 MAINTENANCE MANUAL
Pull the captain's control column aft to the column stop.Make sure that the angle from the neutral column position to the aft stop is at least 13.00 degrees.
 NOTE: Approximately a 65-pound (290 newton) pull is
____ necessary to make sure that the column touches the stop.
Let the control column go to the neutral position.
Do the steps that follow to make sure the control column travel
 with the stabilizer at its limits of travel are correct:
 1) Remove the DO-NOT-CLOSE tags and close these circuit

 breakers on the P11 panel:
 a) 11B19, STAB TRIM ALT (IF INSTALLED)
 b) 11C12, STAB TRIM SHUTOFF LEFT
 c) 11C13, STAB TRIM SHUTOFF RIGHT

 2)  Put the RIGHT and CENTER STAB TRIM SHUTOFF valve switches on the P10 panel to the NORM position.
 3)  AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND; use the STAB TRIM levers to move the horizontal stabilizer in the airplane nose down direction until the stabilizer stops.
 4)  AIRPLANES WITH ALTERNATE STAB TRIM SWITCHES ON THE CONTROL STAND; use the alternate stab trim switches to move the horizontal stabilizer in the airplane nose down direction until the stabilizer stops.
 5) Turn the captain's control wheel full clockwise and hold. 6) Move the captain's control column to the forward stop, to
 the aft stop and to the neutral position. 7) Let the control wheel go to its neutral position. 8) Make sure that the control column moves smoothly and freely
 through full travel. 9) Turn the captain's control wheel full counterclockwise and hold. 10) Move the captain's control column to the forward stop, to the aft stop and to the neutral position.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 02 Page 568 ú May 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 11) Let the control wheel go to its neutral position. 12) Make sure that the column moves smoothly and freely through full travel.
 13) AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND; use the STAB TRIM levers to move the horizontal stabilizer in the airplane nose up direction until the stabilizer stops.
 14) AIRPLANES WITH ALTERNATE STAB TRIM SWITCHES ON THE CONTROL STAND; use the alternate stab trim switches to move the horizontal stabilizer in the airplane nose up direction until the stabilizer stops.
 15) Make sure that the control columns move smoothly and freely through full travel.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(32)