S 865-002
 (1)  
Supply electrical power (Ref 24-22-00).

 S 865-003

 (2)  
Put the R, L and C FLT CONTROL SHUTOFF switches on the right side panel, P61, to the OFF position.

 S 865-004

 (3)  
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:

 (a)  
11H17, FLT CONT SHUTOFF TAIL LEFT

 (b)  
11H18, FLT CONT SHUTOFF TAIL CTR

 (c)  
11H28, FLT CONT SHUTOFF TAIL RIGHT

 S 015-005
 (4)  
Open the access door for the forward equipment bay, 113AL (Ref 06-41-00).

 S 035-006

 (5)  
Do these steps to disconnect the aft end of the first officer's control rod from the elevator forward quadrant:

 (a)  
Loosen the bolts that hold the crank to the shaft on the elevator forward quadrant.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-23
 ALL  ú ú 01 Page 501 ú Sep 20/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

OVERRIDE ASSEMBLY A-A Control Column Override Assembly Adjustment Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-23
 ALL  ú ú 01 Page 502 ú Dec 20/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
CONTROL COLUMN
AGAINST THE AFT STOP
ATTACHMENT POINT FOR THE FORCE GAGE (FINGER REFERENCE POINT)
FWD
ELEVATOR
FORWARD
QUADRANT

CONTROL ROD
SEE B
B-B
TENSION
REGULATOR

1
QUADRANT
SPLINED SHAFT
BOLT BOLTS
CRANK
CONTROL ROD FWD
ELEVATOR FORWARD QUADRANT
1A TENSION REGULATOR IS NOT INSTALLED IN THE FIRST OFFICER'S
B
FORWARD QUADRANT. Control Column Override Assembly Adjustment Figure 501 (Sheet 2)
CONTROL WHEEL
CONTROL COLUMN AGAINST THE FORWARD STOP
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-23
 ALL  ú ú 03 Page 503 ú Dec 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (b)  
Lower the crank to permit access to the bolt that connects the control rod to the crank.

 (c)  
Disconnect the control rod from the crank.

 NOTE: Move the control rod to make sure that it will not get
____ caught when you move the control column.
 S 495-007
 (6)  
Install the adapter equipment (if it is available) for the control wheel to the first officer's control wheel.

 S 485-008

 (7)  
Install the force gage to one of these locations:

 (a)  
On the adapter equipment (if it is installed) for the control wheel on the first officer's control wheel

 (b)  
At the finger reference point on the control wheel.

 E.
Adjust the Override Assembly (Fig. 501)

 S 865-009
 (1)  
Push the captain's and the first officer's control columns forward and do the steps that follow:

 (a)  
Hold the captain's control column forward (against the forward stop).

 (b)  
Pull the first officer's control column aft with the force gage until the control column starts to move.

 (c)  
Make sure the breakout force is 33.5-37.5 pounds (149-166 newtons).

 NOTE: The cam follower bearing breaks out of detent at the cam
____
 on the override assembly.

 (d)  Let the control columns go to the neutral position.
 S 865-010
 (2)  
Pull the captain's and the first officer's control columns aft and do the steps that follow:

 (a)  
Hold the captain's control column aft (against the aft stop).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(132)