(4)  
Set the MCDP to off.

 (5)  
Remove electrical power if not necessary (Ref 24-22-00).

 S 864-027
 S 864-028
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-03
 ALL  ú ú 01 Page 406 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 AFCS GO-AROUND SWITCHES - REMOVAL/INSTALLATION
______________________________________________
 1.  General_______
 A.  Six AFCS go-around switches are found in the engine thrust levers. Three switches are installed in the side of each thrust lever. The Removal/Installation procedure is the same for each set of switches.
 TASK 22-11-04-004-001
 2.  Remove the AFCS Go-Around Switches (Fig. 401).__________________________________
 A.  Access
 (1)  Location Zones
 211/212 Flight Compartment

 B.  Remove the AFCS Go-Around Switches
 S 864-002
 (1)  
Set the two F/D switches on the MCP to OFF.

 S 864-003

 (2)  
Open these circuit breakers on the overhead circuit breaker panel, P11, and attach DO-NOT-CLOSE tags:

 (a)  
11E16, MODE CONT PNL LEFT

 (b)  
11E17, FLT CONT COMPUTER POWER LEFT

 (c)  
11E18, FLT CONT COMPUTER SERVO LEFT

 (d)  
11E20, FLIGHT CONT CMPTR PWR CENTER

 (e)  
11E21, FLIGHT CONT CMPTR SERVO CENTER

 (f)  
11E34, MODE CONT PNL RIGHT

 (g)  
11E35, FLT CONT CMPTR PWR RIGHT

 (h)  
11E36, FLT CONT CMPTR SERVO RIGHT

 (i)  
11F14, TMC AC

 (j)  
11F15, TMC DC

 (k)  
11F16, TMC SERVO

 (3)  
Remove the screws and the cover from the thrust lever.

 (4)  
Remove the screws from the applicable switch and actuator assembly.

 (5)  
Remove the heat shrink tubing from the wiring terminals.

 (6)  
Unsolder the wires from the switch.

 S 034-004
 S 024-005
 S 034-006
 S 024-007
 TASK 22-11-04-404-008
 3.  Install the AFCS Go-Around Switches (Fig. 401)___________________________________
 A.  Equipment
 (1)  Heat gun - commercially available
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-04
 ALL  ú ú 01 Page 401 ú Mar 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

AFCS GO-AROUND SWITCH
NOTE: SPRING REMOVED FOR CLARITY.

AFCS Go-Around Switches Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-04
 ALL  ú ú 01 Page 402 ú Mar 20/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 B. Consumable Materials
 (1)  G02104 Heat Shrink Tubing, R876, color yellow,
 Raychem Corp, 300 Constitution Dr., Menlo Park,
 CA 94025

 C. References
 (1)  
22-00-02/201, Autoflight BITE

 (2)  
24-22-00/201, Electrical Power - Control

 D. Access
 (1)  Location Zones
 211/212 Flight Compartment

 E. Install the AFCS Go-Around Switches
 S 434-009
 (1)  
Apply the heat shrink tubing. Do not shrink the tubing until after the wires are soldered to the switch.

 S 424-010

 (2)  
Solder the wires to the new switch.

 S 434-011

 (3)  
Shrink the heat shrink tubing over the wire terminals.

 S 424-012

 (4)  
Install the switch and actuator assembly with the screws.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 1(114)