Autothrottle System - Inspection/Check
Figure 601 (Sheet 9)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 76-12-00
 ALL  ú ú N01 Page 612 ú Feb 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
B30938
S 226-015-N00
 (16) Do an inspection of the autothrottle servomotor and brake assembly (Fig. 601):
 (a)  
Remove the autothrottle servomotor and brake assembly
 (AMM 76-11-05/401).

 (b)  
Remove the locknut on the brake shaft assembly.

 (c)  
Remove the brake shaft from the assembly.

 (d)  
Do a check on these components for the correct wear limits as shown in the table: 1) One bearing (1), four bearings (5), four bearings (11),

 four bearings (49), one shaft (2, 4), five rotors (3, 3A, 6, 12), one bracket (7), five end cap assemblies (8, 14), five rotor/end cap assemblies (10, 16), ten stators (9, 15), four autothrottle housing assemblies (13, 45, 47, 51, 55), eight bushings (43, 48, 53, 56), four rod end bearings
 (33) and the eight bolts (34, 44, 46, 50, 52, 54).
 2)  If the dimensions of the component exceed the given wear limit, do the applicable repair.
 (e)  Assembly the autothrottle brake assembly: 1) Lightly coat all mating surfaces with MIL-G-23827 grease. 2) Install the shaft. 3) Install the locknut.
 a)  Tighten the nut to 100-150 pound-inches more than the run-on torque.
 b)  The housing of the break/support assembly must have a minimum of 0.10 inch of axial travel when you install the locknut.
 (f)  Install the autothrottle servomotor and brake assembly (AMM 76-11-05/401).
 S 226-016-N00
 (17) Do an inspection of the thrust lever position resolvers (Fig. 601):
 (a)  
Remove the ceiling panels to get access to the thrust lever position resolvers (referred to as the resolvers) (AMM 25-22-01/401).

 (b)  
Remove the resolvers (Ref 76-11-02/401).

 (c)  
Disconnect the rod assemblies from the resolver cranks.

 (d)  
Do a check on these components for the correct wear limits as shown in the table: 1) Four Resolver cranks (35, 41), four shafts (40), four

 bearings (39), four rod end bearings (33), four bushings (36, 37), and four bolts (34, 38, 42). 2) If the dimensions of the components more than the given wear limit, do the applicable repair.

 (e)
Assemble the rod assembly connection to the resolver crank.

 1)  Install the four bolts, nuts, and bushings. a) Use BMS5-95 wet sealant when you install the bushings.

 (f)  
Install the resolvers (AMM 76-11-02/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 76-12-00
 ALL  ú ú N02 Page 613 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 416-017-N00
 (18)
 Install the ceiling panels (AMM 25-22-01/401).

 S 416-018-N00

 (19)
 Install the thrust lever rails of the control stand (AMM 76-11-03/201).

 S 416-019-N00

 (20)
 Install the side panels of the control stand (AMM 76-11-03/201).

 S 416-020-N00

 (21)
 Install the thrust lever cover of the control stand (AMM 76-11-03/201).

 S 416-021-N00

 (22)
 Install the switch covers of the thrust lever assembly (AMM 76-11-03/201).

 S 446-022-N00

 (23)
 Energize the thrust lever switches (AMM 76-11-03/201).

 S 446-023-N00

 (24)
 Energize the flap lever RVDT (AMM 76-11-03/201).

 S 446-024-N00

 (25)
 Energize the actuation circtuis for the speed brake lever (AMM 76-11-03/201).

 S 446-026-N00

 (26)
 Energize the thrust lever position resolvers (AMM 76-11-03/201).

 S 446-027-N00

 (27)
 Energize the interlock actuators of the reverse thrust lever (AMM 76-11-03/201).

 S 446-028-N00

 (28)
 Adjust the thrust lever assemblies (AMM 76-11-01/501).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(53)