76-11-02
ALL ú ú N02 Page 510 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 865-045-N00
(16) Move the No. 2, No. 3 and No. 4 thrust levers forward from the idle position until the thrust lever knobs align with the thrust lever knob of the No. 1 thrust lever.
NOTE: Move the thrust levers forward smoothly from the idle
____ position to prevent hysteresis during the thrust lever adjustment. If you move the thrust lever more than necessary, put the thrust lever back to the idle position and do this step again.
S 975-046-N00
(17)
Make a record of the API display value for the angular distance of movement for the position resolver for the No. 2 thrust lever.
S 975-047-N00
(18)
Subtract the API display value of the angular distance of movement for the position resolvers for the No. 3 and 4 thrust levers, from 90 degrees.
(a) Make a record of the API display value.
S 825-048-N00
(19)
Make sure the difference between the adjusted API display values of the position resolvers is not more than 1.5 degrees.
S 825-049-N00
(20)
If one of the API display value at full forward thrust or full reverse thrust is not in the limits or if the thrust lever knob is not aligned in the specified limits, do the steps that follow:
(a)
Adjust the thrust lever assemblies again (AMM 76-11-01/501).
(b)
Adjust the position resolvers again.
(21)
Disconnect the pulse generator, multimeter, counter, and API.
(22)
Make sure all clamps for the position resolver body are tight.
(23)
Make sure all adjustment nuts for the connecting rod are tight.
S 435-053-N00
(24)
Connect the electrical connectors as follows:
(a)
P1 of T1742 for the position resolver of the No. 1 thrust lever
(b)
P1 of T1743 for the position resolver of the No. 2 thrust lever
(c)
P1 of T1744 for the position resolver of the No. 3 thrust lever
(d)
P1 of T1745 for the position resolver of the No. 4 thrust lever
S 085-050-N00
S 435-051-N00
S 435-052-N00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
76-11-02
ALL ú ú N02 Page 511 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 415-054-N00
(25)
Install the ceiling panels (AMM 25-22-01/401).
S 435-055-N00
(26)
Install the side panels on the control stand (AMM 76-11-03/201).
S 865-056-N00
(27)
Energize the position resolvers, thrust lever switches, and interlock actuators for the reverse thrust lever (AMM 76-11-03/201).
S 865-057-N00
(28)
Do the activation procedure for the captain and first officer seats (AMM 76-11-03/201).
TASK 76-11-02-825-058-N00
3. Calibrate the Thrust Lever Position Resolver (Alternative Procedure)____________________________________________________________________ (Fig. 501 and 503)
A. General
(1)
You can use the alternative adjustment procedure of the thrust lever if you do not have the sinewave generator, digital multimeter, universal counter, or angle position indicator to use. But, the recommended adjustment procedure of the position resolver use the external equipment on the airplane. It is less possible that an error will occur when you use the external equipment and not the airplane EICAS screen.
B.
Special Tools and Equipment
(1)
G12001 Kit-Rig Pin
(a)
TL1, MS20392-4C or equivalent 0.309-0.311 inch (7.85-7.90 mm) diameter rod or bolt by 12.0 inches (305 mm) in length.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(19)
