TASK 51-24-07-307-021
 7.  Apply Corrosion Preventative Paint__________________________________
 A. Equipment
 (1)  
Stainless steel pressure pot liners and mixing equipment

 (2)  
Metal Sieve - 60 to 80 mesh

 (3)  
DeVilbiss MBC or JGA gun - EX needle and tip, 30 or 36 air cap or Binks No. 18 gun 66 X 66, SD nozzle assembly, or equivalent; air pressure 45 to 55 psi.

 (4)  
DeVilbiss MBC or JGA gun - FX needle and tip, 704 or 765 air cap, or Binks No. 18 gun 63 X 63, PB nozzle assembly, or equivalent; Fluid pressure 10 to 20 psi and air pressure 50 to 70 psi.

 B. Consumable Materials
 (1)  
C00298 Primer - BMS 10-11, Type I

 (2)  
C00130 Primer - BMS 10-79, Type II

 (3)  
C00175 Primer - BMS 10-79, Type III

 (4)  
C50016 Coating - BMS10-100 Flexiable Corrosion Inhibiting

 (a)  
Aeroflex Base G12E25

 (b)  
Ultraflex Base 763-66-9200

 (5)  
C00662 Thinner, C25/90S

 (6)  
B00068 Alcohol - Ethyl, MIL-A-6091 or OE-760B,
 Grade 2

 (7)  
B00080 Alcohol - Butyl, TT-B-846

 (8)  
B00528 Toluene (Toluol) - TT-T-548

 (9)  
B00151 Solvent - Methyl Isobutyl Ketone (MIBK),
 TT-M-268

 (10)
 B00192 Solvent - General Purpose, BMS 3-2, Type I

 (11)
 B00316 Solvent - Aliphatic Naphtha, TT-N-95

 (12)
 B00079 Solvent - Normal Butyl Acetate, TT-B-838

 (13)
 B00139 Solvent - Lacquer Thinner, TT-T-266a

 (14)
 B00148 Solvent - Methyl Ethyl Ketone (MEK),
 TT-M-261

 (15)
 B00344 Cleaner - Xylene, TT-X-916

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 51-24-07
 ALL  ú ú 01 Page 710 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (16)
 G00033 Cloth - Cheesecloth, BMS15-5

 (17)
 G50123 Tack Rags - C-60

 (18)
 G00382 Paper - Abrasive, Aluminum Oxide,
 280-Grit or Finer

 C. References
 (1)  AMM 51-24-11/701, Decorative Paint System
 D. Apply the Corrosion Preventive Paint (BMS10-100)
 S 377-022
 (1)  Shake the mixture by hand or power mix for 10 to 15 minutes. The aluminum pigment must be fully mixed.
 NOTE: Do not get air bubbles in the mixture.
____ If it is necessary, you can add C25/90S thinner to make the mixture thin (up to 20 percent, by volume, of the base)
 The working life of the material is 8 hours.
 S 377-023
 (2)  
If it is necessary, rework the BMS 10-11 and BMS 10-20 primed surfaces. Let the primer dry before you apply the corrosion inhibiting finish (AMM 51-24-11/701).

 S 377-024

 (3)
Put the mixture through a clean cloth filter before you use it.

 S 377-025

 (4)  
Apply the mixture with a spray gun until you have a dry layer with a thickness of 2 to 3 mils.

 NOTE: If you get a dry spray condition with BMS10-100 you can
____ decrease the atomizing pressure or you can make the mixture thin with C25/90S thinner.
 (a)  Allow each layer to dry for a minimum of 30 minutes.
 S 377-026
 (5)  Let the topcoat air dry at 65 to 85°F for a minimum of 4 hours before you move the material. Let the material dry for 24 hours before you use the material.
 NOTE: You can use heat on the surface to decrease the cure time.
____ Increase the temperature of the surface to 125 |5°F for 2 hours.
 TASK 51-24-07-307-027
 8. Rework and Repair Damaged Surfaces
___________________________________
 A. Consumable Materials
 (1) G00382 Paper - Abrasive, Aluminum Oxide, 280-Grit or Finer
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 51-24-07
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 結構 STRUCTURES(44)