S 377-008
(2) Apply the finish in an area that will have a good flow of air. Keep a temperature more than 65°F and a relative humidity of 85 percent or less. Apply the finish with a brush to a thickness of 1 to 2 mils (0.001 to 0.002 inch).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-02
ALL ú ú 01 Page 702 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(3) S 377-009Apply the finish on the surface with an overlap of 1/4 inch minimum. To seal the edge of decals, apply the finish to the decal with a 1/4 inch overlap of both the decal and the adjacent surface.
(4) S 377-010Cure the finish. (a) Cure the finish for 4 hours at a minimum of 65°F .
NOTE:____ A full cure is 14 days at a minimum of 65°F.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-02
ALL ú ú 01 Page 703 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
CONDUCTIVE COATING SYSTEM FOR EXTERIOR FIBERGLASS - CLEANING/PAINTING
_____________________________________________________________________
1. General_______
A. This procedure contains one task. The task is to apply conductive coating on external fiberglass.
B. For radome see AMM 53-52-01
TASK 51-24-03-307-001
2. Apply Conductive Coating (Fig. 701)________________________
A. Equipment
(1)
Multimeter - commercially available
(2)
Aluminum Foil Strips or Copper Tape (two with the same dimensions and properties)
B. Consumable Materials
(1)
C00767 Coating - Anti-Static/Conductive, BMS 10-21, Type III
(2)
G00382 Paper - Abrasive, Aluminum Oxide, 240-grit (minimum)
(3)
G00034 Cheesecloth
(4)
G00270 Tape, Masking - Aluminum Foil Adhesive
(5)
G00000 Tape - Adhesive, Aluminum Foil - Permacel P112
(6)
G00115 Sheeting - Transparent, Polyethylene Film - PS 17-64
(7)
B00083 Solvent - Aliphatic Naphtha - TT-N-95
(8)
C00130 Primer BMS 10-79, Type II
(9)
C00175 Primer BMS 10-79, Type III
C. References
(1)
AMM 51-21-02/701, Prepaint Cleaning and Treatment
(2)
AMM 51-24-11/701, Decorative Paint System
D. Procedure
S 117-009
WARNING: DO NOT GET PAINT MATERIALS AND SOLVENTS IN YOUR MOUTH, IN YOUR
_______ EYES, ON YOUR SKIN, OR ON YOUR CLOTHES. DO NOT BREATHE THE FUMES FROM THESE MATERIALS. MAKE SURE THE AIR FLOWS FREELY THROUGH THE WORK AREA. USE THE NECESSARY RESPIRATORY PROTECTION. KEEP THESE MATERIALS AWAY FROM SPARKS, FLAME, AND HEAT. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY OR DAMAGE.
(1) Clean and prepare the surface (AMM 51-21-02/701).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-03
ALL ú ú 01 Page 701 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FIBERGLASS SKINS (UPPER AND LOWER ON WING AND STABILIZER, LEFT AND RIGHT ON FIN, UPPER WING/BODY FAIRING PANELS)
Fiberglass Panel Areas
Figure 701
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-03
ALL ú ú 01 Page 702 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 結構 STRUCTURES(32)
