(a)
Remove the wire clamp from the transmitter.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 10 Page 401 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A SEE B
FWD A TRANSMITTER POSITION RUDDER PEDAL
CONTROL ROD
1
1 "T" MARK ON THE TRANSMITTER SHAFT
B
Rudder Pedal Position Transmitter Installation Figure 401 (Sheet 1)
M27116
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 11 Page 402 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
D
Rudder Pedal Position Transmitter Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 14 Page 403 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
M27131
A
747-400 MAINTENANCE MANUAL
(b)
Disconnect the electrical connector from the transmitter.
(c)
Remove the clamping bolts and nuts.
(d)
Remove the position transmitter.
TASK 27-08-02-404-005
3. Rudder Pedal Position Transmitter Installation (Fig. 401)______________________________________________
A. Special Tools and Equipment
(1)
G12001-50 Rig Pin Kit
B.
References
(1)
24-22-00/201, Manual Control
(2)
25-22-01/401, Main Passenger Compartment Ceiling Access Panels
(3)
IPC 27-21-06 Fig. 5
(4)
SSM 27-09-05
(5)
WDM 27-09-31
(6)
WDM 20-90-11
C.
Access
(1)
Location Zone
212 Passenger Cabin - Nose to First Door, RH
D.
Install the Transmitter
S 864-015
(1)
Make sure that the rudder pedals are in the neutral position.
S 424-006
(2)
Install the transmitter:
(a)
Put the position transmitter in the clamping bracket.
(b)
Line up the "T" mark on the transmitter shaft with the clamping bracket and the "EZ" mark on the transmitter body (Fig. 401).
(c)
Install the clamping bolts and nuts.
(d)
Tighten the clamping bolts and nuts.
(e)
Connect the electrical connector.
(f)
Install the wire clamp to the transmitter.
S 864-028
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6 Main Power Distribution Panel
1) 6J23 COL/RUD PEDAL IND
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 14 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
2) 6J22 COL/RUD PEDAL SENSOR
E. Adjust the Transmitter
S 864-027
(1)
Do this task: "Supply Electrical Power" (Ref 24-22-00/201).
(a)
Install the rig pin R-5 and rig pin R-3 at the same time and make sure they can be installed freely (Fig. 401).
NOTE: On some airplanes, a 3/16 inches pin is required for
____ rig pin R-5. On other airplanes, a 5/16 inches pin is required for rig pin R-5. For 3/16 inches pin, use G12001-6. For 5/16 inches pin, use G12001-14.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(32)
