27-11-10
 ALL  ú ú 04 Page 210 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 092-022
 (12)
 Remove all the rig pins.

 S 082-023

 (13)
 Remove the straightedge from the aileron control wheels.

 S 482-024

 (14)
 Install a protractor and an adapter on the control wheel.

 S 982-044

 (15)
 Move the control wheel to the neutral position.

 S 822-046

 (16)
 Adjust the protractor to zero.

 S 862-025

 (17)
 Do this task to pressurize hydraulic systems No. 1 and 4 or 2 and 3: "Hydraulic System Pressurization" (Ref 29-11-00/201).

 S 712-026

 (18)
 Make sure the ailerons are in the specified neutral tolerance.

 (a)  
Turn the control wheel 58 degrees clockwise. 1) Make sure the right aileron moves up and the left aileron moves down.

 2)  Make sure the displacement is 20.66-20.86 inches (19 to 21 degrees) from the neutral position.
 NOTE: The displacement is measured from the inboard
____ trailing edge (TE) of the inboard aileron to the outboard TE of the inboard flap.
 (b)  Turn the control wheel 58 degrees counterclockwise. 1) Make sure the left aileron moves up and the right aileron moves down.
 2)  Make sure the displacement is 20.66-20.86 inches (19 to 21 degrees) from the neutral position.
 F.  Put the Airplane Back to its Usual Condition
 S 092-027
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  Do this task: "Removal of the Door Locks from the Wing Landing Gear" (Ref 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-10
 ALL  ú ú 04 Page 211 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-028
 (2)  
Do this task: "Hydraulic System Depressurization"
 (Ref 29-11-00/201).

 S 082-029

 (3)
Remove the protractor and the adapter from the control wheel.

 TASK 27-11-10-302-030
 4.  Aileron Programmer Repair_________________________
 A. General
 (1)  
This procedure contains the task to repair the aileron programmer.

 (2)  
To repair the aileron programmer, you must replace the rivets in the controlled shear joint of the quadrant and coupling. This repair is for the left and right programmers.

 B. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 201 | 1 | Quadrant | 27-11-10 | 01| 275 | | | 14 | Aileron Programmer (RH) | 27-11-08 | 01| 525 | | | 21 | Aileron Programmer (LH) | | | 520 | | | 42 | Shaft | 27-11-10 | 01| 300 | | | 43 | Cover | | | 80 | | | 44 | Bolt | | | 225 | | | 45 | Washer | | | 235 | | | 46 | Nut | | | 240 | | | 47 | Pin | | | 200 | | | 49 | Nut | | | 210 | | | 50 | Washer | | | 215 | | | 51 | Cotter Pin | | | 205 | | | 52 | Coupling | | | 255 | | | 53 | Shear Rivet | | | 250 | 2......…........…...................................…...........….....…........1
 C. Access
 (1)  Location Zone
 135 Wing Landing Gear Well, LH
 136 Wing Landing Gear Well, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-10
 ALL  ú ú 04 Page 212 ú Feb 15/98
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(126)