S 348-162

 (2)  
After the filler is hard, rub it with abrasive paper to the same level as the surface of the panel.

 S 348-050

 (3)  
If this is a decorative panel, do the procedure to repair the decorative surface.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 25-00-00
 ALL  ú ú 01A Page 802 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 G. Repair Large Dents in Crushed-Core Panels
 NOTE: This procedure is for panels less than 0.25 inch thick with
____
 dents that are more than 0.005-inch deep.

 S 888-054
 CAUTION: BE CAREFUL WHEN YOU APPLY HEAT NEAR MATERIALS THAT CAN BURN.
_______ THE TEMPERATURE OF THE TEDLAR MUST NEVER BE MORE THAN 200°F OR THE TEMPERATURE AT WHICH THE TEDLAR DISTORTS, WHICHEVER IS LOWER. TOO MUCH HEAT CAN CAUSE DAMAGE TO THE TEDLAR.
 (1)  On the side that does not have dents, increase the temperature of the panel. Use a standard 1200 to 1500 watt handgun, until the panel is approximately 200°F.
 NOTE: The area of the panel will get more flexible, and very
____ hot. Refer to 20-11-25/201 for cautions to obey when you use heat guns.
 S 348-128
 (2)  
Push the backside of the panel forward with the round surface of a tool to remove as much of the dent as you can.

 S 348-056

 (3)  
After the panel is cool, do the procedure to repair small scratches and dents, if it is necessary.

 H. Repair Small Holes and Gouges
 NOTE: Use this procedure for damage that is less than 0.5 square
____
 inch and goes through the face sheets, but not into the
 fiberglass.

 S 348-129
 (1)  
Remove loose and broken pieces, contamination, and other unwanted material from the hole.

 (2)
Clean the area with a cheesecloth that is soaked with naphtha.

 S 118-058
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 25-00-00
 ALL  ú ú 01A Page 803 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 118-059
 (3)  
Dry the area with a clean cheesecloth.

 S 348-054

 (4)
Use the manufacturer's instructions to mix the Epocast 1618A/B.

 S 348-163

 (5)  
Fill the hole with the adhesive mixture (Epocast).

 S 348-090

 (6)  
Let the compound cure for 7 days at 75-79 degrees F, or 5 hours at 120-130 degrees F.

 S 348-164

 (7)  
Rub the area with abrasive paper until it is at same level as the adjacent surface.

 S 348-052

 (8)  
If it is a decorative panel, do the procedure to repair the decorative surface.

 I. Repair Panels that do not have Core Damage
 NOTE: Use this procedure to repair panels that have more than
____ 0.5 inch of damage but no core damage.
 S 348-165
 (1)  
Remove the damaged part of the panel skin.

 S 348-166

 (2)  
Rub the area and 2 inches more on all the sides of the area with abrasive paper until the area is not glossy.

 S 118-109

 (3)
Clean the area with a cheesecloth that is soaked with naphtha.

 (4)  
Dry the area with a clean cheesecloth.

 S 348-167

 (5)  
Follow the manufacturer's instructions to mix the BMS 8-201 resin and hardener.

 S 348-161

 (6)  
Apply glass fabric that is soaked with the mixed adhesive and make an overlap of approximately 1/2-inch.

 S 118-110
 NOTE: Use 50 percent more glass fabric than the initial skin.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 1(8)