(c)  
Push <ADVANCE.

 (d)  
Make sure that these messages show:

 ENGAGE FAIL RIGHT
 ENGAGE FAIL CENTER

 (e)  
Continue with the instructions shown on the CDU until the POSITIVE LIMIT and NEGATIVE LIMIT page is shown.

 (f)  
Push the LSK adjacent <POSITIVE LIMIT.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-10-00
 ALL  ú ú 03 Page 577 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g)  
Write down the value for the elevator surface position: ______ DEG.

 (h)  
Make sure that the value for the left channel is -2.9 degress maximum.

 (i)  
Make sure that the control column stays at the positive limit and the AUTOPILOT DISC does not show on the main EICAS display.

 (j)  
Push the LSK adjacent to <CONTINUE to go back to the POSITIVE LIMIT and NEGATIVE LIMIT page.

 (k)  
Push the LSK adjacent to <ADVANCE to complete the test.

 NOTE: An autopilot disconnect warning will occur at the end
____ of this test which is permitted.
 (l)  Push the autopilot disconnect switch (captain's or first officer's) two times.
 S 745-324
 (4)  Do steps (3) thru (3)(l) again for the right channel.
 NOTE:____Engage fail messages for the right channel are: ENGAGE FAIL LEFT and ENGAGE FAIL CENTER.
 NOTE: The value for the right channel is -2.9 degrees maximum
____
 (same as the left channel).

 S 745-325
 (5)  Do steps (3) thru (3)(l) again for the cemter channel.
 NOTE:____Engage fail messages for the center channel are: ENGAGE FAIL LEFT and ENGAGE FAIL RIGHT.
 NOTE: The value for the center channel is -2.9 degrees maximum
____
 (same as the left channel).

 S 865-326
 (6) Remove pressure from the auxiliary pitot system (Ref 34-11-00/201).
 W. Aileron Autopilot Servo and Surface Limit Test
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-10-00
 ALL  ú ú 01 Page 578 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-152
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
 SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER.  AILERONS, RUDDERS,
 ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
 CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER.  THIS CAN

 CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Make sure you supply hydraulic pressure to the hydraulic systems N0. 1, 2, 3, and 4 (Ref 29-11-00/201).

 S 865-153

 (2)  
Make sure the FLT CONTROL HYD POWER TAIL 1, 2, 3, and 4 switches are in the NORM position. These switches are on the Pilots' Overhead Maintenance Panel (P461).

 S 865-154

 (3)  
Make sure the FLT CONTROL HYD POWER WING 1, 2, 3, and 4 switches are in the NORM position. These switches are on the Pilots' Overhead Maintenance Panel (P461).

 S 865-162

 (4)  
Set the flap lever in the FLAP UP position.

 S 865-163

 (5)  
Set the aileron trim to the center position:

 (a)  
Operate the trim switch until the rig pin A/S-2 can go into the rig hole freely (Ref 27-11-08/201).

 (b)  
Remove the rig pin.

 S 745-155
 (6)  Do this check on the aileron surface position:
 (a)  Push the LSK adjacent to <GROUND TEST from the CMC MENU page on the CDU.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-10-00
 ALL  ú ú 01 Page 579 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護(hù)手冊 空調(diào) AUTO FLIGHT(69)