S 864-027
 (4)  
Put the FLT CONTROL HYD POWER WING 1, 2, 3,AND 4 switches tothe SHUTOFF position. The switches are on the Pilot's Overhead Maintenance Panel (P461).

 S 864-028

 (5)  
Open these circuit breakers and attach the DO-NOT-CLOSE tags:

 (a)  P7 Overhead Circuit Breaker Panel
 1) 7D12, FLT CONT CMPTR C SERVO
 2) 7D13, FLT CONT CMPTR C PWR
 3) 7E9, MCP L
 4) 7E18, MCP R

 (6)  
Put in the #2 and #3 rigging pins (Fig. 401).

 (7)  
Install the control wheel straightedge tool (Fig. 401).

 S 834-029
 S 484-058
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-13-01
 ALL  ú ú 01 Page 404 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 F. Procedure
 S 024-030
 (1)  Remove the LAS.
 (a)  
Disconnect the electrical connector from the LAS (6). Put caps on the electrical connector and on the LAS electrical port.

 (b)  
Put a bucket under the area where the hydraulic lines are attached to the LAS.

 WARNING: DO NOT LET HYDRAULIC FLUID GET INTO YOUR EYES, MOUTH, OR
_______ ONTO YOUR SKIN. THE FLUID CAN CAUSE INJURY.
 (c)  
Disconnect the hydraulic lines from the LAS (6) and drain the fluid into the bucket.

 (d)  
Put caps on the hydraulic lines and on the LAS hydraulic ports.

 (e)  
Remove the bolt (1) and the bushing (2) that connect the control rod to the LAS crank arm.

 (f)  
Hold the LAS (6) and remove the mounting bolts (3), the washers (4), and the nuts (5).

 (g)  
Remove the LAS (6).

 TASK 22-13-01-404-065
 3. Lateral Autopilot Servo Installation (Fig. 401 and 402)
____________________________________
 A. Parts
 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT |FIG | ITEM | ................................................................................ | 402 | 1 | Bolt | 27-11-08 | 01 | 135 | | | 2 | Bushing | | | 140 | | | 3 | Bolt | 22-13-01 | 01 | 10 | | | 4 | Washer | | | 15 | | | 5 | Nut | | | 20 | | | 6 | Autopilot Servo Assy, Lateral | | | 5 | 2......…........…...................................…............…....…........1
 B. Standard Tools and Equipment
 (1)  Bonding Meter - Autron T477W
 C. Consumable Materials
 (1)  A00247 Sealant - Chromate type BMS5-95,class B-2
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-13-01
 ALL  ú ú 01 Page 405 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 D. References
 (1)  
20-22-01/601, Electrical Bonding

 (2)  
22-10-00/501, Autopilot/Flight Director System

 (3)  
24-22-00/201, Manual control

 (4)  
AMM 27-11-08/201, Central Leteral Control Package

 (5)  
29-11-00/201, Main Hydraulic Supply System

 (6)  
32-00-30/201, Landing Gear Door Locks

 (7)  
IPC 22-13-01, Fig. 1

 (8)  
IPC 27-11-08, Fig. 1

 E. Access
 (1)  Location Zone
 135 Wing Landing Gear Well, LH

 F. Prepare for the Installation
 S 864-031
 (1)  Supply electrical power (Ref 24-22-00/201).
 S 494-061
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Do this task: "Body Landing Gear Door Lock Installation"
 (Ref 32-00-30/201).

 S 864-071
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AUTO FLIGHT(111)