(c)
If the SENS, WARN, and FLAG lights come on, inspect the connector pins on the rear of the R/T and the mating connector on the rack for bent pins and damage. Repair or replace as required.
(d)
If the SENS, WARN, and FLAG lights still come on, replace the applicable receive or transmit antenna (Ref 34-48-11/401) or repair/replace the coaxial cables connected to the antennas, as required.
(e)
The warn flag in the HI should be out of view if the system is operational.
(f)
If the warn flag on the HI is still in view, make a check of the wiring between the HI and the applicable R//T.
C. HI Troubleshooting
(1) These faults usually occur in the HI. Replace the HI if you see one or more of these faults.
NOTE: If the fail warn flag on the HI is in view after the HI is
____ replaced, continue on with the troubleshooting procedures.
(a)
Dial lights (all malfunctions).
(b)
DH light (all malfunctions).
(c)
Self-test pushbutton or DH control knob/cursor/counter (all malfunctions).
(d)
Warn flag not in view when the circuit breaker is pulled.
D. ADI DH Light Troubleshooting
(1) For an attitude director indicator (ADI) with a DH light, press the DH light face to test for a failed lamp in the DH light assembly.
(a)
Replace the DH light or DH light assembly, as required.
(b)
If the DH light still does not come on, replace the ADI.
E. Put the airplane in its usual condition at the completion of troubleshooting.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú
34-48-00
ú ú 06 Page 102 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
LOW RANGE RADIO ALTIMETER SYSTEM - MAINTENANCE PRACTICES
________________________________________________________
1. General
_______
A. This subject contains one task. The task simulates radio altitude with a Bendix/King AMT-51A Radio Altimeter Test Set connected to Bendix ALA-51A radio altimeters.
TASK 34-48-00-722-036
2. Radio Altitude Simulation (BENDIX/KING AMT-51A Radio Altimeter Test Set).
_________________________
A. General
(1)
Use this procedure with Bendix receiver/transmitters (R/Ts) that have dc (analog) radio altitude output.
(2)
Do these procedures in sequence.
B. Standard Tools and Equipment
(1) Bendix/King AMT-51A Radio Altimeter Test Set
C. References
(1)
24-22-00/201, Manual Control
(2)
34-48-00/501, Low Range Radio Altimeter System
(3)
34-48-03/501, Low Range Radio Altimter System
D. Access
(1) Location Zone
101/102 Control Cabin
205 Electronics Compartment
E. Prepare for Radio Altitude Simulation
S 712-050
(1) Do the LRRA Operational Test (Ref 34-48-00/501 or 34-48-03/501, as applicable) to make sure the radio altimeter system and its display interfaces operate correctly.
NOTE: Do not do the decision height (DH) tests since DH is not
____ necessary for radio altitude simulation.
Do not turn off the systems energized in the operational test. This will decrease the time to do the radio altitude simulation procedures.
S 712-051
(2)
AIRPLANES WITHOUT EFIS;
Set the decision height to 600 feet on the HIs.
S 712-052
(3)
AIRPLANES WITH EFIS;
Do these steps:
(a)
Set the EFIS transfer switch (P5 overhead panel) to the NORMAL position.
(b)
Set the decision height to 600 feet on the EFIS control panels.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 3(138)
