FRAMES AND BULKHEADS – DESCRIPTION AND OPERATION
1.  General
A.  A typical fuselage frame is illustrated in figure 1. Each frame is a zee-section circumferential member, with increased web depth at floor level. The frames are generally spaced at twenty-inch intervals along the fuselage.
B.  The bulkhead at body station 178 is the forward end of the pressure cabin, and is composed of four vertical beams and a flat pressure web which the beams divide into small panels.
C.  At body station 227.8 a frame, with a web extending across the lower part of it, is installed. The web forms the forward wall of the nose landing gear wheel sell. At body station 294.5 another frame, with a web extending across the lower part of it, is installed. This web forms the aft wall of the nose landing gear wheel well.

H29144 H30561
500  Typical Fuselage Structure 
May 15/67  Figure 1 (Sheet 1)  53-11-0 
Page 1 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

 Typical Fuselage Structure  500 
53-11-0  Figure 1 (Sheet 2)  May 15/67 
Page 2 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

D.  At body station 259.5 a frame with increased web depth marks the aft end of the control cabin. The transverse floor beam at body station 259.5 lying across the top of the nose landing gear wheel well ceiling has its web extended downwards between the fuselage skin and the nose landing gear wheel well sidewalls.
E.  At body station 360 a bulkhead extends across the fuselage from floor level and down to form the forward wall of the forward cargo compartment.
F.  At body station 540 a bulkhead extends across the fuselage from floor level and down. This bulkhead serves as the aft wall of the forward cargo compartment and the front spar of the center wing box.
G.  At body station 664 a bulkhead extends across the fuselage from floor level and down. This bulkhead serves as the aft spar of the center wing box and the forward wall of the main landing gear wheel well.
H.  At body station 727 a bulkhead extends across the fuselage from floor level and down. This bulkhead serves as the aft wall of the main landing gear wheel well and the forward wall of the aft cargo compartment.
I.  The pressure bulkhead at body station 1016 is a curved web extending aft like a dome in the vertical plane. The web is reinforced with radii stringers all originating at the center of the web. The web forms the aft end of the pressurized cabin. The vertical fin front spar attach fittings are at the top of the fuselage at body station 1016. See figure 2.
J.  The bulkhead at body station 1088 incorporates the vertical fin rear spar attach fittings. A rectangular cutout in the web allows the forward part of the horizontal stabilizer center section truss to protrude through it. The horizontal stabilizer jackscrew mechanism is attached to the forward side of the bulkhead web.
K.  The bulkhead at body station 1156 incorporates the horizontal stabilizer center section truss hinge joints. Elevator control mechanisms are attached to the aft side of the bulkhead. The lower part of the bulkhead is cut away to allow or the APU exhaust pipe.
500 
May 15/67  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  53-11-0 Page 3 

H29147
Aft Pressure Bulkhead  500 
53-11-0Page 4   Figure 2 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  May 15/67 

STRINGERS AND OTHER LONGITUDINAL MEMBERS - DESCRIPTION AND OPERATION
1.  General
A.  The fuselage stringers, which start at body station 259.5, are hat-section members along the entire fuselage. Refer to Chapter 53 of the Structural Repair Manual for stringer identification.
B.  Typical attachments of stringers to skin and frames are shown in 53-11-0. Some stringers just above and below the floor beams are attached to the frames by an additional fitting. The continuity of the stringers is maintained across the production joints in the fuselage structure by terminating the stringers on each section at a fitting which is attached to the production joint frame.
C.  A horizontal beam extends along each side of the fuselage level with the top of the floor. These beams are known as the crease beams because they are attached to the fuselage skin at the "crease" formed by the intersection between the upper and lower lobes of the fuselage cross-section. Along their outboard edges the crease beams are attached to the skin by a continuous chord, or stringer. The inboard chord of each beam consists of a continuous angle attached to the inboard edges of the frames and the upper edges of the floor beams. Between its continuous outboard and inboard chords the crease beam consists of a series of webs which individually extend from frame to frame.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 機身 FUSELAGE(4)