3. Fault Confirmation
__________________
 A. Do the operational test of the engine interface unit through the CFDS (Ref. AMM TASK 73-25-34-710-043).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message CHECK EIU 1 ARINC OUTPUT CIRCUIT TO FADEC OR EIU 1:
 - do a check for 28VDC at EIU 1 pins AC/9, 11.
 (1) If there is 28VDC:

 - replace the EIU-1 (1KS1) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040) (Ref. ASM 73-25/05).

 (2) If the fault continues:

 - do a check and repair the J3 harness from the EIU 1 (1KS1) to the ECU (4000KS) pins AB/5C, 5A to pins J3/22, 23 (Ref. ASM 73-25/06).

 (3) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 254
 E E Feb 01/05 ERE ECES

 F 『 E C F M E E E E 56 E E E

 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 255
 E E Feb 01/00 ERE
ECES

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 73-25-00-810-886
 Loss of Data on EIU to FADEC Bus for Engine 2
 1. Possible Causes
_______________
 - EIU-2 (1KS2)

 - J3 harness from the EIU 2 to the ECU (4000KS)

 - ECU (4000KS)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU)
 (1KS1,1KS2)
 AMM 73-25-34-710-043 Operational Test of the Engine Interface Unit
 ASM 73-25/05
 ASM 73-25/06

 3. Fault Confirmation
__________________
 A. Do the operational test of the engine interface unit through the CFDS (Ref. AMM TASK 73-25-34-710-043).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message CHECK EIU 2 ARINC OUTPUT CIRCUIT TO FADEC OR EIU 2:
 - do a check for 28VDC at EIU 2 pins AC/9, 11.
 (1) If there is 28VDC:

 - replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040) (Ref. ASM 73-25/05).

 (2) If the fault continues:

 - do a check and repair the J3 harness from the EIU 2 to the ECU (4000KS) pins AB/5C, 5A to pins J3/22, 23 (Ref. ASM 73-25/06).

 (3) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 256
 E E Feb 01/05 ERE ECES

 F 『 E C F M E E E E 56 E E E

 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 257
 E E Feb 01/05 ERE
ECES  TASK 73-25-00-810-889

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E

 Loss of the A/THR Control on Engine 1
 1. Possible Causes
_______________
 - EIU-1 (1KS1)

 - harness J3 between the EIU (1KS1) and the ECU (4000KS)

 - wiring between the FCU (2CA) and the EIU (1KS1)

 - FCU (2CA)

 - FMGC (1CA1)

 - ECU (4000KS)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 22-81-12-000-001 Removal of the FCU (2CA)
 AMM 22-81-12-400-001 Installation of the FCU (2CA)
 AMM 22-83-34-000-001 Removal of the FMGC (1CA1,1CA2)
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發(fā)動機燃油和控制 2(53)