(3) If the test gives the maintenance message J8, HMU(FMVRES), ECU:
- disconnect the J8 harness from the HMU receptacle (HMU-B) (located in the left core compartment) and visually examine the J8 harness connector and the HMU receptacle for damaged pins, contamination and fuel wetting (Ref. AMM TASK 73-21-50-210-002).
(a) If damage on a connector is found:
- Replace or repair as required.
(b) If fuel wetting is found:
- replace the harness J8, (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
(c) If nothing is found:
- Do an electrical resistance test through the HMU receptacle between: . pins 16 and 34 (34 to 46 or 85 to 150 Ohms) . pins 35 and 36 (21 to 29 or 44 to 76 Ohms) . pins 18 and 37 (21 to 29 or 44 to 76 Ohms) . pins 16 and 17 (> 10 Megohms) . pins 35 and 17 (> 10 Megohms) . pins 18 and 17 (> 10 Megohms) . pin 16 and the ground (> 10 Megohms) . pin 35 and the ground (> 10 Megohms) . pin 18 and the ground (> 10 Megohms).
1 If the resistance values are out of the specified limits:
_
- replace the Hydromechanical Unit (HMU), (Ref. AMM TASK 73-21-10-000-002) and (Ref. AMM TASK 73-21-10-400-002).
F 『 EEFF : ALL E ∞∞73-29-00∞∞∞∞∞∞∞∞∞∞Page A221
E E May 01/05 ERE ECES
F 『 E C F M E E E E 56 E E E 2 If the resistance values are in the specified limits:
_
- reconnect the harness J8, (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041) and continue the troubleshooting.
(d) Disconnect the J8 harness from the ECU (4000KS) receptacle and visually examine the J8 harness connector and the ECU (4000KS) receptacle for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage on a connector is found:
_ - replace or repair as required.
2 If nothing is found:
_
- Do an electrical resistance test through the J8 harness between: . pins 16 and 34 (34 to 46 or 85 to 150 Ohms) . pins 35 and 36 (21 to 29 or 44 to 76 Ohms) . pins 18 and 37 (21 to 29 or 44 to 76 Ohms) . pins 16 and 17 (> 10 Megohms) . pins 35 and 17 (> 10 Megohms) . pins 18 and 17 (> 10 Megohms) . pin 16 and the ground (> 10 Megohms) . pin 35 and the ground (> 10 Megohms) . pin 18 and the ground (> 10 Megohms).
a If the resistance values are in the specified limits:
_
- replace the ECU (4000KS), (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
b If the resistance values are out of the specified limits:
_
- replace the harness J8, (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
B. Do the test given in Para. 3.A.(1).
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞73-29-00∞∞∞∞∞∞∞∞∞∞Page A222
E E May 01/05 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
TASK 73-29-00-810-868
Loss of the FMV Torque Motor Control through the Channel A on Engine 1
1. Possible Causes
_______________
- ECU (4000KS)
- Hydromechanical Unit (HMU)
- harness J7
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-10-000-002 Removal of the Hydromechanical Unit (HMU) AMM 73-21-10-400-002 Installation of the Hydromechanical Unit (HMU) AMM 73-21-50-000-040 Removal of the HJ7 Harness AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 73-21-50-400-040 Installation of the HJ7 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
(ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring)
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 1A on the ground (with engine non - motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. Do this procedure:
NOTE : This fault is generated if there is an open or short to ground in 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 2(125)
