(5) Do the detailed visual inspection of the MLG (LH) uplock units and pins (Ref. AMM TASK 32-31-00-200-001).
(6) Correct any fault found.
(7) Do the functional test of the normal extension and retraction of the landing gear (Ref. AMM TASK 32-31-00-720-002).
(8) If the fault continues, the MLG (LH) is slow to operate or the fault continues after the subsequent flight, replace the ACTG CYL-MLG L (2503GM) (Ref. AMM TASK 32-31-46-000-001) and (Ref. AMM TASK 32-31-46-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A239
Aug 01/05R
CES
TASK 32-31-00-810-864
MLG (RH) Does Not Downlock
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
1. Possible Causes
_______________
- MLG (RH) proximity sensors and target clearances
- MLG (RH) lockstay assembly
- MLG (RH) downlock springs
- ACTG CYL-MLG R (2504GM)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 32-11-00-200-001 Inspection/Check of the Main Gear AMM 32-11-00-220-003 Detailed Dimensional Check of the MLG Lockstay Assembly AMM 32-11-19-200-001 Visual Check of Main Landing Gear Downlocking Springs and Sidestay Center Joint Links and Cuffs AMM 32-31-00-200-001 Detailed Inspection of Gear Uplock and Door Uplock Units and Pins AMM 32-31-00-720-002 Functional Test of the Normal Extension and
Retraction of the Landing Gear AMM 32-31-46-000-001 Removal of the MLG Actuating Cylinder AMM 32-31-46-400-001 Installation of the MLG Actuating Cylinder AMM 32-31-73-200-001 Inspection of the MLG Proximity Sensor and Target
Clearances
AMM 32-33-00-720-001 Functional Check of Free-Fall Extension
3. Fault Confirmation
__________________
A. Procedure
(1) If it was necessary to do a gravity extension of the landing gear, do the Aircraft Configuration procedure (Ref. AMM TASK 32-33-00-720-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A240
Aug 01/05R CES
(2) Do a check of the post flight report. If there is a L/G SYS DISAGREE ECAM message and related MLG (RH) downlock target-position CFDS message, do the Fault Isolation procedure.
4. Fault Isolation
_______________
A. Procedure NOTE : The procedure that follows, gives the information necessary to
____
identify mechanical faults related to the MLG (RH).
(1) Do the inspection/check of the main gear (RH) (Ref. AMM TASK 32-11-00-200-001).
(2) Do the inspection of the MLG (RH) proximity sensors and target clearances (Ref. AMM TASK 32-31-73-200-001).
(3) Do the detailed dimensional check of the MLG (RH) lockstay assembly (Ref. AMM TASK 32-11-00-220-003).
(4) Do the visual inspection of the MLG (RH) downlock springs (Ref. AMM TASK 32-11-19-200-001).
(5) Do the detailed visual inspection of the MLG (RH) uplock units and pins (Ref. AMM TASK 32-31-00-200-001).
(6) Correct any fault found.
(7) Do the functional test of the normal extension and retraction of the landing gear (Ref. AMM TASK 32-31-00-720-002).
(8) If the fault continues, the MLG (RH) is slow to operate or the fault continues after the subsequent flight, replace the ACTG CYL-MLG R (2504GM) (Ref. AMM TASK 32-31-46-000-001) and (Ref. AMM TASK 32-31-46-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A241
Aug 01/05R
CES TASK 32-31-00-810-865
NLG Does Not Uplock
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 1(55)
