Loss of the input bus from the SDAC 2 to the DMC 1
1. Possible Causes
_______________
- DMC-1 (1WT1)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
AMM 31-60-00-740-007 GROUND SCANNING Test of the DMC
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
ASM 31-54/04
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU EIS/SDAC/2/SPLY 2WV Q06
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
B. Test Do the EIS input test (EIS 1) (Ref. AMM TASK 31-60-00-740-002).
R **ON A/C 401-499,
B. Test Do the Ground Scanning Test of the DMC (Ref. AMM TASK 31-60-00-740-007).
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
A. If the test gives the maintenance message:
DMC1 : NO SDAC2 DATA
- replace the DMC-1 (1WT1), (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the DMC 1 (1WT1) pins AA/10G, 10H to the first terminal block , (Ref. ASM 31-54/04).
R **ON A/C 401-499,
A. If the test gives the maintenance message:
SDAC2(1WV2)/DMC1(1WT1)
- replace the DMC-1 (1WT1), (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the DMC 1 (1WT1) pins AD/6C, 6D to the first terminal block , (Ref. ASM 31-54/04).
**ON A/C ALL
B. Do the test given in Para. 3.B.
Loss of the input bus from the SDAC 2 to the DMC 2
1. Possible Causes
_______________
- DMC-2 (1WT2)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
AMM 31-60-00-740-007 GROUND SCANNING Test of the DMC
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
ASM 31-54/04
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU EIS/SDAC/2/SPLY 2WV Q06
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
B. Test Do the EIS input test (EIS 2) (Ref. AMM TASK 31-60-00-740-002).
R **ON A/C 401-499,
B. Test Do the Ground Scanning Test of the DMC (Ref. AMM TASK 31-60-00-740-007).
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
A. If the test gives the maintenance message:
DMC 2 : NO SDAC2 DATA
- replace the DMC-2 (1WT2), (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the DMC 2 (1WT2) pins AA/10G, 10H to the first terminal block , (Ref. ASM 31-54/04).
R **ON A/C 401-499,
A. If the test gives the maintenance message:
SDAC2(1WV2)/DMC2(1WT2)
- replace the DMC-2 (1WT2), (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the DMC 2 (1WT2) pins AD/6C, 6D to the first terminal block , (Ref. ASM 31-54/04).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 2(88)
