Loss of the FMC 2 Output Bus by the DMC 3
 1. Possible Causes
_______________
 - DMC-3 (1WT3)

 - wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
 AMM 31-60-00-740-007 GROUND SCANNING Test of the DMC
 AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
 AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 ASM 31-62/01

 3. Fault Confirmation
__________________
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
 -------------------------------------------------------------------------------
121VU AUTO FLT/FMGC/2 10CA2 M17
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 B. Test
 Do the EIS input test (Ref. AMM TASK 31-60-00-740-002).

R **ON A/C 401-499,
 B. Test Do the Ground Scanning Test of the DMC (Ref. AMM TASK 31-60-00-740-007).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-00∞∞∞∞∞∞∞∞∞∞Page A278
 Aug 01/05 CES 4. Fault Isolation

_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 A. If the test gives the maintenance message DMC 3 : NO FMC 2 DATA:
 - replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
 (1) If the fault continues:
 - do a check and repair the wiring from the DMC 3 (1WT3) pins AA/4J, 4K to the first terminal block (Ref. ASM 31-62/01).
R **ON A/C 401-499,
 A. If the test gives the maintenance message FMGC2(1CA2)BUS FM2/DMC3(1WT3):
 - replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
 (1) If the fault continues:
 - do a check and repair the wiring from the DMC 3 (1WT3) pins AA/3J, 3K to the first terminal block (Ref. ASM 31-62/01).
 **ON A/C ALL
 B. Do the test given in Para. 3.B.

 Loss of the FAC 1 Output Bus by the DMC 1
 1. Possible Causes
_______________
 - DMC-1 (1WT1)

 - wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
 AMM 31-60-00-740-007 GROUND SCANNING Test of the DMC
 AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
 AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 ASM 22-65/01
 ASM 31-62/01

 3. Fault Confirmation
__________________
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 B. Test
 Do the EIS input test (Ref. AMM TASK 31-60-00-740-002).

R **ON A/C 401-499,
 B. Test Do the Ground Scanning Test of the DMC (Ref. AMM TASK 31-60-00-740-007).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-00∞∞∞∞∞∞∞∞∞∞Page A280
 Aug 01/05 CES 4. Fault Isolation

_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 A. If the test gives the maintenance message DMC 1 : NO FAC 1 DATA:
 - replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
 (1) If the fault continues:

 - do a check and repair the wiring from the DMC 1 (1WT1) pins AA/3C, 3D to the first terminal block (Ref. ASM 31-62/01).

 (2) If the fault continues:

 - do a check and repair the wiring from the DMC 1 (1WT1) pin AB/1K to the first terminal block (Ref. ASM 22-65/01).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 2(76)