- C/B-FUEL/RFL/DFL/SUPPLY (2QU) - supplies 28VDC to the refuel valves.
NOTE : The refuel valves (all) will not open if the 28VDC, 501PP
____ FUELLING BUS is not powered. This is because the Fuel Level Sensing System (FLSS) high level channels (all) will give false WET outputs when they are not powered (de-energized condition).
(3) If during the test of the CTL PNL-REFUEL/DEFUEL (800VU), the HI LVL lights fail to operate as specified:
- refer to P. Block 101, LOCAL WARNING INDICATORS for the related Trouble-shooting Task number.
(4) Look at the STATUS REPORT (BITE) of the FLSS (Ref. AMM TASK 28-46-00-740-001).
(5) If the FUEL LEVEL SENSING message, L(R) HI LEVEL SENSOR 17QT1(2) is given:
- do the procedure for L(R) High Level Sensor 17QJ1(2) Failure (Ref. TASK 28-46-00-810-803) before you start more steps.
(6) If the FUEL LEVEL SENSING message, C HI LEVEL SENSOR (20QJ) is given:
- do the procedure for C High Level Sensor 20QJ Failure (Ref. TASK 28-46-00-810-805) before you start more steps.
(7) If, in Manual Refuel all the refuel valves fail to open:
- go to Para. 4.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞28-25-00∞∞∞∞∞∞∞∞∞∞Page 221
May 01/04R CES
(8) If, in Manual Refuel one refuel valve fails to open:
- use the related manual plunger to attempt to continue the refuel as given in the procedure for Pressure Refuel without Electrical Power (Ref. AMM TASK 12-11-28-650-005).
(9) If, during the time the related refuel valve manual plunger is held pushed in:
(a) The applicable refuel valve opens and the refuel continues:
- go to Para. 4.B.
(b) The applicable refuel valve does not open and fuel cannot be put into the related fuel tank:
- go to Para. 4.C.
4. Fault Isolation
_______________
A. Procedure - In Manual Refuel All Refuel Valves Fail To Open
(1) Remove the CTL PNL-REFUEL/DEFUEL (800VU) and disconnect the two connectors 4023VC-A and 4024VC-A (Ref. AMM TASK 28-25-55-000-001).
(2) Use a multimeter to do a test (Ref. ASM 28-25/01) to see if 28VDC is available between pin <G (+ve), of the end connector 4023VC-A, and a suitable ground.
(3) If 28VDC is available at pin <G go to step (4). If 28VDC is not available at pin <G:
(a) Do a check of and replace, if necessary, the
C/B-FUEL/RFL/DFL/SUPPLY (2QU).
(b) If 28VDC is not available at the 501PP FUELING BUS 1:
- do the procedure for Refueling not Possible Failure (Ref. TASK 24-67-00-810-801).
(c) Do a wiring check of the aircraft wiring (Ref. ASM 28-25/01) between:
- the C/B-FUEL/RFL/DFL/SUPPLY (2QU) and the CTL PNL-REFUEL/DEFUEL (800VU) end connector 4023VC-A, pin <G.
(d) Repair all the unserviceable wiring and connectors.
(e) Install the CTL PNL-REFUEL/DEFUEL (800VU) (Ref. AMM TASK 28-25-55-400-001).
(f) Do the Manual Refuel (Ref. AMM TASK 12-11-28-650-004).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞28-25-00∞∞∞∞∞∞∞∞∞∞Page 222
May 01/04R
CES
(4) Do the step (a) or (b) that follows:
(a) Replace the CTL PNL-REFUEL/DEFUEL (800VU) with a serviceable item and install (Ref. AMM TASK 28-25-55-000-001) and (Ref. AMM TASK 28-25-55-400-001).
(b) If due to airline operational conditions it is not possible to replace the CTL PNL-REFUEL/DEFUEL (800VU), do the internal Trouble-shooting (Ref. ASM 28-25/01) and (Ref. ASM 28-25/03) as follows:
1 Remove the CTL PNL-REFUEL/DEFUEL (800VU) (Ref. AMM TASK 28-25-
_
55-000-001).
2 Do a check of and replace, if necessary, the SW-MODE
_ SELECT/REFUEL/OFF/DEFUEL/XFR (3QU).
3 Do a check of the CTL PNL-REFUEL/DEFUEL (800VU) internal
_ wiring (Ref. ASM 28-25/03) between:
- the receptacle 4023VC, pin <G and terminal 1A, of the terminal block 4001VT
- the terminal 1D, of the terminal block 4001VT and the terminal 1B, of the SW-MODE SELECT/REFUEL/OFF/DEFUEL/XFR (3QU)
- the terminal 3B, of the SW-MODE SELECT/REFUEL/OFF/DEFUEL/XFR (3QU) and the terminal 3D, of the terminal block 4001VT.
NOTE : Terminal 3D, of the terminal block 4001VT is the last
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 FUEL 燃油2(69)
