- replace the defective unit.

 B. Electric Test
 (1) Do the operational test of the Emergency generation system (Ref. AMM TASK 24-24-00-710-001).
 (a) Do the trouble shooting given in Para. 4.B. when, during the operational test:
 1  on the lower ECAM display unit:
_
 - the line between AC 1 bus and AC ESS bus comes on,

 - the line between DC 1 bus and DC ESS bus comes on,

 - the line between EMER GEN and AC ESS bus goes off,

 - the line between EMER GEN and ESS TR goes off,

 - the EMER GEN voltage and frequency come on green.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-24-00∞∞∞∞∞∞∞∞∞∞Page 211
 May 01/03 CES

 (b) Do the trouble shooting given in Para. 4.C. when, during the operational test:
 1 on the lower ECAM display unit:
_
 - the line between AC 1 bus and AC ESS bus comes on,

 - the line between DC 1 bus and DC ESS bus comes on,

 - the EMER GEN voltage and frequency are shown in amber.

 (c) Do the trouble shooting given in Para. 4.D. when, during the operational test:
 1 on the lower ECAM display unit:
_
 - the line between DC 1 bus and DC ESS bus comes on,

 - the line between ESS TR and DC ESS bus goes off.

 (d) Do the trouble shooting given in Para. 4.E. when, at the end of the operational test:
 1 on the EMER ELEC PWR section of the panel 21VU:
_
 - when the EMER GEN TEST pushbutton switch is released, the CSM/G and the Blue electric pump do not stop automatically.
R (e) Do the trouble shooting given in Para. 4.F. when, during the
R operational test:

R 1_ On the EMER ELEC PWR section of the panel 21VU:
R - when you push the EMER GEN TEST pushbutton switch (23XE) and
R also when you keep it pushed, the CSM/G (8XE) and the blue
R electrical pump (2075GJ) start and stop after 10 seconds.

 4. Fault Isolation
_______________
 A. Table of the circuit breakers used in this procedure:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------105VU ELEC/CSM/G /EV AUTO/SPLY 7XE C01 106VU CSM/G /EV/MAN/SPLY 6XE B04 106VU ESS TR/CNTOR/CTL 5PE C02
 B. If the test confirms the fault:
 - replace the RELAY-EMER CONDITION (12XE).
 (1) If the fault continues:
 - do a check and repair the wiring between respectively: . the pin X of the CSM/G control unit (1XE) and the pin A/X of the EMER CONDITION relay (12XE) . the pin A/Z of this relay (12XE) and the ground (Ref. ASM 24-24/02).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-24-00∞∞∞∞∞∞∞∞∞∞Page 212
 May 01/03 CES C. If the test confirms the fault:

 - on the EMER ELEC PWR panel 21VU, open the guard, push and hold the EMER GEN TEST pushbutton switch and at the same time do a check for 28VDC on the pin A/b of the CSM/G control unit (1XE) (Ref. ASM 24-24/02)
 NOTE : There is 28VDC during 6 s only.
____
 (1) If there is 28VDC:

 - replace the CONTROL UNIT-CSM/G (1XE) (Ref. AMM TASK 24-24-34-000-001) and (Ref. AMM TASK 24-24-34-400-001).
 (a) If the fault continues:

 - replace the CSM/G (8XE) (Ref. AMM TASK 24-24-51-000-001) and (Ref. AMM TASK 24-24-51-400-001).

 (b) If the fault continues with the Blue electric pump in operation:

 - replace the ELEC PUMP-B (2075GJ) (Ref. AMM TASK 29-12-51-000-001) and (Ref. AMM TASK 29-12-51-400-001).

 (2) If there is not 28VDC:

 - replace the RELAY-EMER GEN TEST CONDITION (16XE), RELAY-EMER AUTO LOG CONDITION (17XE), RELAY-EMER AUTO LOG CONDITION (18XE), RELAY-RAT EXTN INHIB CONDITION (20XE), RELAY-CSM/G EV SPLY MONG (22XE), RELAY (3PH), RELAY-BUS 1XP CTL (15XC), RELAY-BUS 2XP CTL (16XC) and P/BSW-EMER ELEC PWR/EMER GEN TEST (23XE).

 (3) If the fault continues:

 - do a check of the status of the circuit breakers (6XE) and (7XE).
 (a) If they are closed:
 - do a check and repair the wiring between respectively: . the circuit breaker (6XE) and the pin 7 of the pushbutton (23XE) . the pin 8 of the pushbutton (23XE) and the pin A/X of the relay (16XE) through the relays (15XC) and (16XC) . the circuit breaker (7XE) and the pins A/X1 and A/B2 of the relay (20XE), through the relays (17XE) and (18XE) . the pin A/X2 of the relay (20XE) and the ground, through the relay (16XE) . the pin A/B1 of the relay (20XE) and the pin A/X1 of the relay (22XE) . the pin A/X2 of the relay (22XE) and the ground . the pin A/B1 of the relay (20XE) and the pin A/b of the CSM/G control unit (1XE), through the relays (22XE) and (3PH) (Ref. ASM 24-24/02).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 3(30)