(2) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-50-00∞∞∞∞∞∞∞∞∞∞Page 237
May 01/00R
CES
TASK 24-50-00-810-812
Loss of the AC BUS 1
1. Possible Causes_______________
R R - IDG (4000XU) - feeders
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R R AMM AMM AMM AMM AMM AWM AWM AWM AWM 24-21-51-000-040 24-21-51-400-040 24-41-00-861-002 24-41-00-862-002 31-60-00-860-001 24-22-0124-51-0524-51-0724-51-09 Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) Installation of the Integrated Drive Generator -IDG 1(2),(4000XU)Energize the Aircraft Electrical Circuits from the External PowerDe-energize the Aircraft Electrical Circuits Supplied from the External PowerEIS Start Procedure
3. Fault Confirmation__________________
A. Job Set-up
(1) Aircraft Maintenance Configuration
(a) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
(b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
B. Test
Do this test:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the ECAM control panel:
- push the ELEC key to get the ELEC page.
4. Fault Isolation
_______________
R A. If the test confirms the fault: On the upper ECAM display unit:
- these warnings come into view:ELEC AC BUS 1 FAULT ELEC AC ESS BUS FAULT ELEC DC ESS BUS FAULT
On the overhead panel, on panel 35VU:
- the FAULT legend of the AC ESS FEED pushbutton switch is on.
R - do a check of the feeders between the GLC1 (9XU1) and the busbar 1XP
R (Ref. AWM 24-51-05), (Ref. AWM 24-51-07) and (Ref. AWM 24-51-09).
R (1) If the feeders are not correct:
R - repair them.
R (2) If the feeders are correct:
R - do a check of the feeders between the GLC1 (9XU1) and the IDG1
R (4000XU) for a short to ground or a short circuit (Ref. AWM 24-22-
R 01).
R (a) If the feeders are not correct:
R - repair them.
R (b) If the feeders are correct:
R - replace the engine 1 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-
R 040) and (Ref. AMM TASK 24-21-51-400-040).
B. Do this test to make sure that the system operates correctly:
-------------------------------------------------------------------------------
ACTION RESULT
-------------------------------------------------------------------------------
On the ECAM control panel: On the lower ECAM display unit:
- push the ELEC key to get the ELEC - the normal configuration comes into
page. view.
5. Close-up
________
A. Put the aircraft back to its initial configuration.
(1) On the ECAM control panel, set the UPPER DISPLAY and LOWER DISPLAY potentiometers to OFF.
(2) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 3(131)
