R (1) Do the BITE test of the GAPCU (Ref. AMM TASK 24-41-00-740-002).

R (a) If the BITE test gives the message TEST FAILED:
R - do the trouble shooting given in Para 4.A.
R (b) If the BITE test gives the message TEST PASSED:

R - do the trouble shooting given in Para 4.B. R 4. Fault Isolation
_______________
R A. If the BITE test gives the message TEST FAILED:
R - push the line key adjacent to the TEST FAILED message.

R (1) If the maintenance message GCU1 (1XU1) comes into view:
R - replace the GCU-1 (1XU1) (Ref. AMM TASK 24-22-34-000-001) and (Ref.
R AMM TASK 24-22-34-400-001).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-20-00∞∞∞∞∞∞∞∞∞∞Page B225
 Aug 01/05 CES

R  B. If the BITE test gives the message TEST PASSED: 
R  - do a check of the wiring for a short to ground between pin B/29 of the 
R  BTC 1 and pin A/4C of the GCU 1 (Ref. ASM 24-22/02). 
R  (1) If there is a short to ground: 
R  - repair or replace as necessary. 
R  (2) If there is no short to ground: 
R  - do a check of the coil return wiring for a short to ground between 
R  pin B/5 of the BTC 1 and pin A/9A of the GCU 1 (Ref. ASM 24-22/02). 
R  (a) If there is a short to ground: 
R  - repair or replace as necessary. 
R  (b) If there is no short to ground: 
R  - do a check of the status auxiliary contact for correct 
R  operation between pin B/27 and pin B/29 of the BTC 1 (normally 
R  open) (Ref. ASM 24-22/02). 
R  1 If there is no continuity:_ 
R  - replace the BTC-1 (11XU1) (Ref. AMM TASK 24-22-55-000-001) 
R  and (Ref. AMM TASK 24-22-55-400-002). 
R  2 If there is continuity:_ 
R  - replace the GCU-1 (1XU1) (Ref. AMM TASK 24-22-34-000-001) 
R  and (Ref. AMM TASK 24-22-34-400-001). 
R  3 If the fault continues:_ 
R  - replace the GLC-1 (9XU1) (Ref. AMM TASK 24-22-55-000-001) 
R  and (Ref. AMM TASK 24-22-55-400-002). 
R  C. Do the test given in para. 3.

R TASK 24-20-00-810-897

R Failure of the BTC 2 or its Status Contact or Wiring R 1. Possible Causes
_______________
R - GCU-2 (1XU2) R - BTC-2 (11XU2) R - GLC-2 (9XU2) R - wiring
R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 24-22-34-000-001 R AMM 24-22-34-400-001 R AMM 24-22-55-000-001 R AMM 24-22-55-400-002 R R AMM 24-41-00-740-002 R ASM 24-22/03
R 3. Fault Confirmation
__________________
R A. Test
Removal of the GCU-1(2) (1XU1, 1XU2)
Installation of the GCU-1(2) (1XU1, 1XU2)
Removal of the Contactors (9XU1, 9XU2, 11XU1, 11XU2)
Installation of the Contactors (9XU1, 9XU2, 11XU1,
11XU2)
Operational Check of GAPCU via CFDS

R (1) Do the BITE test of the GAPCU (Ref. AMM TASK 24-41-00-740-002).

R (a) If the BITE test gives the message TEST FAILED:
R - do the trouble shooting given in Para 4.A.
R (b) If the BITE test gives the message TEST PASSED:

R - do the trouble shooting given in Para 4.B. R 4. Fault Isolation
_______________
R A. If the BITE test gives the message TEST FAILED:
R - push the line key adjacent to the TEST FAILED message.

R (1) If the maintenance message GCU2 (1XU2) comes into view:
R - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref.
R AMM TASK 24-22-34-400-001).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-20-00∞∞∞∞∞∞∞∞∞∞Page B227
 Aug 01/05 CES

R  B. If the BITE test gives the message TEST PASSED: 
R  - do a check of the wiring for a short to ground between pin B/29 of the 
R  BTC 2 and pin A/4C of the GCU 2 (Ref. ASM 24-22/03). 
R  (1) If there is a short to ground: 
R  - repair or replace as necessary. 
R  (2) If there is no short to ground: 
R  - do a check of the coil return wiring for a short to ground between 
R  pin B/5 of the BTC 2 and pin A/9A of the GCU 2 (Ref. ASM 24-22/03). 
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 電源 2(37)