R B. If the BITE test gives the message TEST PASSED:
R - do an electrical resistance test of the IDG 2 disconnect solenoid for
R an open circuit or a high resistance condition between pin A/12 and pin
R A/13 of the IDG 2 (3 ohms plus or minus 1 ohm) (Ref. ASM 24-21/01).

R (1) If the resistance values are out of the specified limits:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040)
R and (Ref. AMM TASK 24-21-51-400-040).

R (2) If the resistance values are in the specified limits:
R - replace the RELAY-IDG 2 DISC CTL (4XT)
R - do a dynamic disconnect test of the IDG 2 (Ref. AMM TASK 24-21-00-R 720-041).

R (a) If the test is OK:
R - stop the trouble shooting.

R (b) If the test is not OK:
R - do a check of the wiring for an open circuit or a short to
R ground between pin A1 of the IDG 2 disconnect control relay
R (4XT) and pin A/12 of the IDG 2 (Ref. ASM 24-21/01).

R 1_ If the wiring is not correct:
R - repair or replace as necessary.

R 2_ If the wiring is correct:
R - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001)
R and (Ref. AMM TASK 24-22-34-400-001).

R a_ If the fault continues:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-R 51-000-040) and (Ref. AMM TASK 24-21-51-400-040).

R C. Do the test given in para. 3.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 401-499, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 249
 Aug 01/05 CESR TASK 24-21-00-810-822 R Failure of the Integrated Drive Generator 1 R 1. Possible Causes

_______________ R - IDG (4000XU) R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 24-00-00-810-808 R R 24-20-00-810-904 R AMM 24-21-51-000-040 R R AMM 24-21-51-400-040 R R AMM 24-41-00-740-002 R AMM 24-41-00-861-002 R R AMM 24-41-00-862-002 R R AMM 31-60-00-860-001 R AMM 31-60-00-860-002 R AMM 71-00-00-710-003 R AMM 71-00-00-710-028
R 3. Fault Confirmation
__________________
R A. Test
R Not applicable.

Failure of the IDG 1 Oil-Out Temperature Bulb or its Wiring Low Oil Pressure of the Integrated Drive Generator 1 Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) Installation of the Integrated Drive Generator -IDG 1(2),(4000XU) Operational Check of GAPCU via CFDS Energize the Aircraft Electrical Circuits from the External Power De-energize the Aircraft Electrical Circuits Supplied from the External Power EIS Start Procedure EIS Stop Procedure Engine Automatic Start Engine Shutdown
R NOTE : As the GEN 1 was set to OFF because of a true failure, the fault
____ R confirmation is not necessary.
R 4. Fault Isolation
_______________
R A. If the fault symptom is identified by the CFDS message IDG1 (E1-4000XU)
R and the upper ECAM-DU warning GEN 1 FAULT:

R (1) If one of these CFDS messages:
R - IDG1 (E1-4000XU) OIL OUT TEMP/ GCU1 (1XU1)
R - IDG1 (E1-4000XU) LOW OIL PRESSURE
R comes into view with IDG1 (E1-4000XU), do the trouble shooting for
R these messages first:

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 250
 Aug 01/05 CES

R (a) Do the procedure for an overtemperature (Ref. TASK 24-00-00-810-
R 808).
R (b) Do the procedure for a low oil pressure (Ref. TASK 24-20-00-810-R 904).

R (2) If the CFDS messages given in step (1) do not come into view:
R - replace the engine 1 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040)
R and (Ref. AMM TASK 24-21-51-400-040).

R B. Do this operational test to make sure that the system operates correctly. R (1) Aircraft Maintenance Configuration R (a) Energize the aircraft electrical circuits
R (Ref. AMM TASK 24-41-00-861-002).
R (b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
R (Ref. AMM TASK 31-60-00-860-001).
R (2) On the ELEC panel 35VU:

R - push, release and push again the GEN 1 pushbutton switch (3XU1).

R (3) Do the operational test of the GAPCU (Ref. AMM TASK 24-41-00-740-R 002).
R (4) Start the engine 1 (Ref. AMM TASK 71-00-00-710-003).
R (5) Do this test:
R -------------------------------------------------------------------------------
R ACTION RESULT R -------------------------------------------------------------------------------
R R R R  On the ECAM control panel: - get the ELEC page.  On the lower ECAM DU: - the correct electrical parameters of the GEN 1 are shown and the AC1 busbar is supplied by the GEN 1. 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 2(115)