(1) If the wiring is not correct:
- repair it.
(2) If the wiring is correct:
- do a check of the resistance between the pins B/7 and B/8, then between the pins B/8 and B/9 of the IDG 1.
NOTE : The normal value is 99.1 Ohms plus or minus 5 Ohms at 25.C.
____
(a) If the oil-out bulb resistance is less than the oil-in bulb resistance:
- replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
(b) If the oil-out bulb resistance is not less than the oil-in bulb resistance:
- replace the GCU-1 (1XU1) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM TASK 24-22-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 214
201-299, 301-399, Aug 01/05 CES
TASK 24-21-00-810-808
Difference in IDG 2 Oil-In/Oil-Out Bulb Tolerances
1. Possible Causes
_______________
- IDG (4000XU)
- GCU-2 (1XU2)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 24-21-51-000-040 Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) AMM 24-21-51-400-040 Installation of the Integrated Drive Generator -IDG
1(2),(4000XU)
AMM 24-22-34-000-001 Removal of the GCU-1(2) (1XU1, 1XU2)
AMM 24-22-34-400-001 Installation of the GCU-1(2) (1XU1, 1XU2)
ASM 24-21/01
3. Fault Confirmation
__________________
A. Test
Not applicable.
NOTE : The BITE test permits to do a check of the GCU only. The fault
____ confirmation related to IDG 2 BULB TOLERANCE is not possible on ground.
4. Fault Isolation
_______________
CAUTION : BEFORE YOU START THE CHECK OF IDG WIRING THAT INCLUDES CONNECTORS,
_______ EXAMINE EACH CONNECTOR TO MAKE SURE THAT THERE IS NO OIL IN IT. IF YOU FIND OIL, CLEAN THE CONNECTOR AND CONNECT IT AGAIN. IF THE FAILURE CONTINUES, DO THE TROUBLE SHOOTING PROCEDURE AS GIVEN BELOW.
A. If the fault symptom is identified by the CFDS message IDG 2 BULB TOLERANCE and the upper ECAM DU warning IDG 1 OIL OVHT:
- do a check of the wiring: . for open circuit between the GCU 2 pin A/9A and the IDG 2 pin B/9 . for short to ground between the GCU 2 pin A/8A and the IDG 2 pin B/7 . for wire cross-connection between respectively the GCU 2 pins A/8A, A/9A, A/9B and the IDG 2 pins B/7, B/9, B/8 (Ref. ASM 24-21/01).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 215
201-299, 301-399, Aug 01/05 CES
(1) If the wiring is not correct:
- repair it.
(2) If the wiring is correct:
- do a check of the resistance between the pins B/7 and B/8, then between the pins B/8 and B/9 of the IDG 2.
NOTE : The normal value is 99.1 Ohms plus or minus 5 Ohms at 25.C.
____
(a) If the oil-out bulb resistance is less than the oil-in bulb resistance:
- replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
(b) If the oil-out bulb resistance is not less than the oil-in bulb resistance:
- replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM TASK 24-22-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 216
201-299, 301-399, Aug 01/05 CES
R **ON A/C ALL
TASK 24-21-00-810-809
The IDG1 Cannot be Disconnected Intentionnally
1. Possible Causes
_______________
- P/BSW-ELEC/IDG 1 (5XT)
- RELAY-IDG1 DISC CTL (3XT)
- RELAY-FUNCTION (7XT)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 2(104)
