(2) Install the splitter fairing (Ref. TASK 72-23-00-400-028).
(3) Install all the fan blades (Ref. TASK 72-21-00-400-007).
(4) Install the spinner rear cone (Ref. TASK 72-21-00-400-006).
F 『 EEFF : ALL E Page 45572-21-00
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(5) Install the spinner front cone (Ref. TASK 72-21-00-400-005).
5. Close-up
________
Subtask 72-21-00-869-065
A. Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 72-21-00-942-064
B. Remove the warning notice(s).
F 『 EEFF : ALL E Page 45672-21-00
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
FAN AND BOOSTER ASSEMBLY - INSPECTION/CHECK
___________________________________________
TASK 72-21-00-210-005
Inspection/Check of the Spinner Cone
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific Torque Wrench : to 4 lbf.in (0.04 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2216 *
Loctite 496 (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
72-00-00-200-025 Over-Serviceable-Limit Extensions 72-21-00-000-005 Removal of the Spinner Front Cone 72-21-00-000-006 Removal of the Spinner Rear Cone 72-21-00-300-001 Replacement of the Crimped Self-Locking Nuts on the
Spinner Rear Cone
72-21-00-400-005 Installation of the Spinner Front Cone
72-21-00-400-006 Installation of the Spinner Rear Cone
R 72-55-00-960-002 Replacement of LPT Shaft Plug O-rings
F 『 EEFF : ALL E Page 60172-21-00
E E Nov 01/99 E E ECES E E 56-5B E
F 『
E C F M E
E E
E E
3. Job Set-up
__________ Subtask 72-21-00-941-078
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 72-21-00-020-072
B. Remove the Spinner Cone.
(1) Remove the spinner front cone (Ref. TASK 72-21-00-000-005)
(2) Remove the spinner rear cone (Ref. TASK 72-21-00-000-006)
4. Procedure
_________ Subtask 72-21-00-210-055
A. Inspection of the spinner cone
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Spinner front cone for:
A. Cracks Not serviceable. Install a new or serviceable spinner front cone (Ref. TASK 72-21-00-400-005).
F 『 EEFF : ALL E Page 60272-21-00
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(95)
