A. Piece missing:  Maximum number 20 blades Refer to maximum up to 0.25 in. (6.5 mm) serviceable limits axial, 0.73 in. (18.5 (Ref. TASK 72-00-00-200-mm) radial on all 025) airfoil surfaces, except top/bottom 0.4 in. (10 mm).
 B. Broken vane:  Not serviceable Replace stage 1 booster vane (Ref. TASK 72-21-00-000-008) and (Ref. TASK 72-21-00-400-008)
 F 『 EEFF : ALL E Page 64472-21-00
 E E Aug 01/04 ERE
ECES  E F 『 E C F M E E E E 56-5B E

 Inspection of Fan Disk
 Figure 608/TASK 72-21-00-991-317

 F 『 EEFF : ALL E Page 64572-21-00
 E E Aug 01/04 ERE
ECES E F 『 E C F M E E E E 56-5B E

 Fan Blades Spacer Figure 609/TASK 72-21-00-991-318
 F EEFF : E ER ECES  ALL  『E 72-21-00EE E Page 646 Aug 01/04

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 INTENTIONALLY BLANK

 F 『R E E Page 64772-21-00
 E E Aug 01/04 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

R R  Stage 1 Booster Vane Damage Limits Figure 610/TASK 72-21-00-991-319- 12 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 72-21-00EEE Page 648 Aug 01/04

R R  Stage 1 Booster Vane Damage Limits Figure 610/TASK 72-21-00-991-319- 22 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 72-21-00EEE Page 649 Aug 01/04

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Disengagement from inner shroud: 
D. Cracks and tears: 
R 
R R R R R R R  E. Distortion of trailing edge and leading edge: 
F. Nicks, dents, scratches for areas A and B: 
R  G. Nicks, dents, scratches for area "C": 
R R R R  H. Nicks, dents, scratches on leading edge and trailing edge 
J. Deposits and erosion: 
K. Cracked inner shroud 

F EEFF : ALL E E ECES Not serviceable
In area C, any number, less than 0.25 in. (6.5 mm) radial less than
0.08 in. (2 mm) axial.
Any number, if the length L is not more than 0.709 in. (18 mm) and the maximum dimension X along the chord width is not more than 0.256 in. (6.5 mm)
Any number, less than
0.09 in. (2.29 mm) in diameter protrusion.
Any number, less than
0.197 in. (5 mm) in diameter protrusion acceptable, not through
Maximum axial length less than 0.08 in. (2 mm) in diameter protrusion acceptable, not thru.
Any amount.
Not serviceable.
『E EEEReplace stage 1 boostervane (Ref. TASK 72-21-00-000-008) and (Ref. TASK 72-21-00-400-008)
Refer to maximumserviceable limits(Ref. TASK 72-00-00-200-025)
Refer to maximum serviceable limits (Ref. TASK 72-00-00-200-025)
Refer to maximumserviceable limits(Ref. TASK 72-00-00-200-025)
Refer to maximumserviceable limits(Ref. TASK 72-00-00-200-025)
Refer to maximum serviceable limits (Ref. TASK 72-00-00-200-025)
Refer to maximumserviceable limits (Ref. TASK 72-00-00-200-025)
Refer to maximumserviceable limits (Ref. TASK 72-00-00-200-025).

72-21-00Page 650
Aug 01/04

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
L. Erosion/flaking of abradable lining on outer shroud
 2. Fan disk for: (Ref. Fig. 608/TASK 72-21-00-991-317)
 A. Cracks
B. Wear on dovetail slot pressure faces.
C. Nicks and
scratches.

3. Fan blade spacer for: (Ref. Fig. 609/TASK 72-21-00-991-318)
 A. Cracks
B. Fretting,
corrosion

5. Close-up
________
 Subtask 72-21-00-420-077
Any amount.

Not serviceable.
No limit, if less than  See limit extensions
50 percent of area is  (Ref. TASK 72-00-00-200-
damaged. If the maximum  025)
 affected surface, even
 only on one side of one
 slot, is greater than or
 equal to 50%, any amount
 if less than 0.152 mm
 (0.0059 in.) deep.
No limited quantity, if  See limit extensions
not deeper than 0.01 in.  (Ref. TASK 72-00-00-200-
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(106)