(b) Disconnect the PS13 hose from the ECU and from the fan frame boss.

 F 『 EEFF : ALL E Page 63872-23-00
 E E May 01/05 ERE
ECES  E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (c) Inspect the connections as follows:

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Fitting nuts for:
 - damaged corners  Any amount, provided
 proper torque can be
 obtained.

 - damaged threads  Any amount, provided Chase the threads.
 effective threads are
 not reduced by more than
 one after chasing.

 - safetywire hole  Serviceable, provided
 deformation and metal around hole is not
 wear. cracked or torn.

 2. Fittings seating surfaces for:
 - circumferential  Any amount not

 scratches  detectable with a 0.04
 in. (1 mm) radius ball
 scribe.

 - axial scratches  Not serviceable Replace the hose or the part.

 - nicks, pits  Not serviceable Replace the hose or the part.

 (2) Clean the weep hole with white spirit (Material No. CP2010) and a plastic wire.

 (3) Blow clean dry air into the PS13 connection to ECU to remove any dirt or water accumulation. Blocked hose is not serviceable. If necessary, replace the hose (Ref. TASK 72-23-00-000-029) and (Ref. TASK 72-23-00-400-029).

 (4) Check the ECU nipple for dirt. If necessary, remove the dirt with a plastic wire. Take care to not introduce dirt inside the ECU.

 F 『 EEFF : ALL E Page 63972-23-00
 E E May 01/05 ERE
ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (5) Check the fan frame boss for dirt. If necessary, remove the dirt with stoddart solvent and a plastic wire. Blow clean dry air into the fan frame boss nipple.

 (6) Lubricate the ECU and the fan frame boss nipples with engine fuel.

 (7) Connect the PS13 line to the ECU and to the fan frame boss.

 (8) TORQUE the ECU connection to between 180 and 200 lbf.in (2.03 and

 2.26 m.daN).

 (9) Safety with lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8002).

 (10) TORQUE the fan frame boss connection to between 135 and 150 lbf.in

 (1.52 and 1.69 m.daN).

 (11) Safety with lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8002).

 5. Close-up
________ Subtask 72-23-00-410-097
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the warning notice(s).

 (4) Remove the access platform(s).

 F 『 EEFF : ALL E Page 64072-23-00
 E E May 01/05 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 72-23-00-280-002
 Inspection/Check of the PS12 line
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific plastic wire
 No specific warning notice
 No specific access platform 1.5 m (4 ft. 11 in.)
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2010 * white spirit (Ref. 70-30-00) Material No. CP8001 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00) Material No. CP8002 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(147)