BACKSHELL LOCKWIRE PROCEDURE - DESCRIPTION AND OPERATION
________________________________________________________
1. General
_______
A. Procedure
(1) This section describes the standard practices for securing a connector, its backshell, and associate parts by the use of Lockwire.
(2) The lockwire is installed to prevent a part from becoming loose. The wire is installed to apply an opposing force so that a part will not disengage.
(3) The geneeral note section on the engineering drawing should specify the type and size of the safety wire to be used. If no instructions exist, use safety wire per MS20995N20.
2. Tools and Equipment
___________________ (See Table 1)
------------------------------------------------| REFERENCE | DESIGNATION | |---------------------|------------------------|
| No Specific | Wire cutters |
| No Specific | Pliers |
| No Specific | Wire twisting pliers |
------------------------------------------------Tools and Equipment Table 1
3. Consumable Material
___________________ (See Table 2)
------------------------------------------------| REFERENCE | DESIGNATION | |---------------------|------------------------| | MS20995N20 | Lockwire | ------------------------------------------------Consumable Material
Table 2
F 『 EEFF : ALL E Page 170-71-45
E E Feb 01/01 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
4. Reference Information_____________________ (See Table 3)
------------------------------------------------| REFERENCE | DESIGNATION | |---------------------|------------------------| | 70-71-41 | Connector backshell | | | replacement parts | ------------------------------------------------
Reference Information Table 3
5. Standard practices for Lockwire_______________________________
A. Procedure
(1) There are three areas of the connector that need safety wiring:
(a) If a not-self-locking coupling nut is used, the coupling nut must be safety wired to a fixed point.
(b) If a backshell is used that provides a saddle clamp for strain relief, the saddle clamp mounting screws must be safety wired.
(c) If a backshell is installed that has safety wiring provisions in the coupling nut, it must be safety wired.
(2) Any non-self-locking coupling nuts used in high vibration areas must be safety wired. This includes the power plant area, and the pylon area. (Ref. Fig. 001)
NOTE : Safety wiring must installed in the direction that fastener or
____
coupler tightening will be maintained.
(3) Where safety wiring is required on a series of two or more equipment mounting screws, the screws must be safety wired with one continuous length of wire. (Ref. Fig. 002)
(4) On strain relief saddle clamps, where a drilled head screw is not provided, replace the existing screw with a drilled fillister head screw of the same strength rating.
(5) All safety wiring is to be of the double twist wire method. (Ref. Fig. 003)
F 『 EEFF : ALL E Page 270-71-45
E E Feb 01/01 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
Safety Wiring Connectors and Strain Relief Clamps
Figure 001
F EEFF : ALL 『E 70-71-45 Page 3
E E Feb 01/01
E E
ECES E
Safety Wiring of Mounting Serews
Figure 002
F 『 EEFF : ALL E Page 470-71-45
E E Feb 01/01 E E ECES E F 『 E C F M E E E E 56-5B E
Connector Lockwiring Steps
Figure 003
F 『 EEFF : ALL E Page 570-71-45
E E Feb 01/01 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(6) safety wire must be installed so that if the item being safety wired becomes loose, it will apply a tightening pull on the attached point.
(7) Safety wiring twists must be uniform. There must be 6 to 10 twists per inch.
(8) Excess wire must be cut square and bent back.
6. Safety wiring procedure
_______________________
CAUTION: LOCKWIRE IS NOT REUSABLE: ALWAYS USE NEW LOCKWIRE.
A. Procedure
- Safety wire the connector, adapter or backshell, as follows:
(1) Pull half the wire through the safety wire hole in the part being safety wired. Pull the right-hand wire end under the other wire end.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES - ENGINES(40)
