-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
49-51-51-991-001 Fig. 401
3. Job Set-up
__________ Subtask 49-51-51-860-051
A. Aircraft Maintenance Configuration
(1)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
(2)
In the cockpit, on APU panel 25VU, make sure that the FAULT and ON legends in p/bsw MASTER SW are off.
(3)
Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
Subtask 49-51-51-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/X FEED/VALVE/BAT 2HV D13 121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
Subtask 49-51-51-010-056
C. Get Access
(1)
Put the access platform in position below the APU access doors 315AL and 316AR.
(2)
Open the APU access doors 315AL and 316AR (Ref. TASK 52-41-00-010-001).
(3)
Make sure that the light SW 11LJ is set to the ON position.
4. Procedure
_________
(Ref. Fig. 401/TASK 49-51-51-991-001) Subtask 49-51-51-420-050
A. Installation of the BLCV (8050KM)
(1)
Remove the blanking caps from the two air ducts.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Hold the valve (6) in position and attach the V-clamp (5). Do not fully tighten the V-clamp at this time.
NOTE : Make sure that the arrow on the valve points in the same
____
direction as the system air flow.
(4)
Attach the valve (8050KM) (6) to the air duct with the V-clamp (4). Do not fully tighten the V-clamp at this time.
(5)
Make sure that there is sufficient clearance between the valve (8050KM) (6) and the adjacent components.
(6)
TORQUE the V-clamp (5) to 0.68 m.daN (60.17 lbf.in).
(7)
TORQUE the V-clamp (4) to 0.56 m.daN (49.55 lbf.in).
(8)
Remove the blanking cap from the air tube (3).
(9)
Connect the air tube (3) to the valve (8050KM) (6).
(10)
Tighten the air tube (3) connection.
(11)
Safety the air tube (3) connection with lockwire - corrosion resistant steel 0.8 mm (0.032 in) dia.
(12)
Remove the blanking caps from the electrical connectors.
(13)
Connect the electrical connector (2) and the electrical connector (1).
Subtask 49-51-51-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/X FEED/VALVE/BAT 2HV D13 121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
Subtask 49-51-51-740-050
C. BITE Test the APU Bleed Air System.
(1)
Energize the CFDS to get the SYSTEM REPORT/TEST page for the APU (Ref. TASK 31-32-00-860-001).
(2)
Set the APU MASTER SW 14KD to ON.
(3)
Do this Test.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
-
push the pushbutton adjacent to the APU indication.
-
push the pushbutton adjacent to the SYSTEM SELF-TEST indication.
2. On the MCDU:
-
push the pushbutton adjacent to the RETURN display.
-
push the pushbutton adjacent to the RETURN display.
On the MCDU:
-
the APU menu page comes on.
-
the APU SYSTEM SELF-TEST page comeson and shows the messageIN PROGRESS.
-if the test is satisfactory, the message TEST OK comes on.
On the MCDU:
-
the APU menu page comes on.
-
the SYSTEM REPORT/TEST page comes on.
-------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER5(28)
