R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
38-30-00-991-003 Fig. 202
**ON A/C 301-399,
38-30-00-991-003-A Fig. 202A
**ON A/C ALL
3. Job Set-up
__________
Subtask 38-30-00-860-054
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized from the external power (Ref. TASK 24-42-00-861-001).
Subtask 38-30-00-560-051
B. Preparation of the Drain lines for Installation R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 202/TASK 38-30-00-991-003)
**ON A/C 301-399,
(Ref. Fig. 202A/TASK 38-30-00-991-003-A)
**ON A/C ALL
(1)
Do an inspection of the component interface and/or the adjacent area.
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Remove the blanking plugs from the disconnected line ends.
(4)
Apply COMMON GREASE (Material No. 04-012) to the new O-rings (2) and install them on the drain line ends.
NOTE : Refer to the relevant (Ref. AIPC 383101), (Ref. AIPC 383102),
____ (Ref. AIPC 383103), (Ref. AIPC 383104) for information of expendable parts.
(5) Install the clamshells (4) over the drain lines before you put the drain lines in position.
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 202/TASK 38-30-00-991-003)
**ON A/C 301-399,
(Ref. Fig. 202A/TASK 38-30-00-991-003-A)R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 38-30-00-420-058
A. Installation of the Toilet Drain Lines
(1)
Examples A, B, C, D, E, F and G.
(a) Put the drain lines (1) in position.
(2)
Example B.
(a)
Put the clamp assemblies (7) and the spacers (8) in position.
(b)
Install the washers (6), the bolts (5) and the nuts (9) but do not tighten them at this time.
(3)
Example C.
(a)
Put the clamps (10) in position.
(b)
Put the washers (6) on the bolts (5).
(c)
Install the bolts (5), the spacers (8), the washers (6) and the nuts (9).
(4)
Example E.
(a)
Put the clamp assemblies (7) in position.
(b)
Install the washers (6), the bolts (5), the washers (6) and the nuts (9) but do not tighten them at this time.
(5)
Example A.
(a)
Move the sleeves (3) over the drain lines (1).
(b)
Install the clamshells (4).
(6)
Examples B, C, and E.
(a) Tighten the bolts (5) and the nuts (9).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 38-30-00Page 223 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(7)
Example D.
(a)
Put the clamps (11) in position.
(b)
Install the washers (6), the bolts (5), the bonding straps (12) and the nuts (9).
(c)
Make sure that the bonding straps are correctlly bonded
(Ref. TASK 20-28-00-912-004).
(8)
Example F.
(a) Installation of the pipes between Frame 35 and frame 36
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE
_______ WORK AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(b)
Clean the clamp and the pipes with CLEANING AGENTS (Material No. 11-003).
(c)
Install the new O-rings (2) on the pipes (1).
(d)
Move the sleeve (3) back over the O-rings (2).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WATER/WASTE 1(110)
