B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00) Material No. 11-002 USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
cotter pin 38-14-02 03A-050
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 38-10-00-614-001 Pressurization of the Potable Water System from a
Ground Air Supply 38-10-00-614-002 Depressurization of the Potable Water System 52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 38-14-49-991-005 Fig. 402
3. Job Set-up
__________
Subtask 38-14-49-860-053
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the system potable water is depressurized (Ref. TASK 38-10-00-614-002).
Subtask 38-14-49-010-061
B. Get Access
(1)
Make sure that the access platform is in position in front of the applicable passenger/crew door 832 or 842.
(2)
Make sure that the passenger/crew door 832 or 842 is open (Ref. TASK 52-10-00-010-001).
(3)
Make sure that the access platform is in position at the drain panel 133AL.
(4)
Make sure that the drain panel 133AL is open.
(5)
Make sure that the warning notice is in position in the drain panel.
(6)
Make sure that the access platform is in position at the service panel 2023VU.
(7)
Make sure that the access door 171AL of the service panel 2023VU is open.
(8)
Make sure that the warning notice is in position in the service panel 2023VU.
(9)
Make sure that the access platform is in position at the door 825.
(10) Make sure that the FWD cargo-compartment door 825 is open (Ref. TASK 52-30-00-860-001).
(11) Make sure that the CARGO COMPT LIGHT switch 6LU is at ON. R (12) Make sure that in the FWD cargo-compartment, the floor panels 131EF,
R 131FF, 131GF are removed. Subtask 38-14-49-865-060
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
124VU SVCE/601PP/602PP/SPLY 1PX BB01
4. Procedure
_________
(Ref. Fig. 402/TASK 38-14-49-991-005)
Subtask 38-14-49-560-053
A. Preparation for Installation WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1)
Clean the lever (5), the bush (6), the bearing assy (7) and the handle (8) with CLEANING AGENTS (Material No. 11-002).
(2)
Apply COMMON GREASE (Material No. 04-004) to the bush (6) and the bearing assy (7).
Subtask 38-14-49-420-053
B. Installation of the Control Handle
(1)
Do an inspection of the component interface and/or the adjacent area.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WATER/WASTE 1(103)
