52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 30-73-53-991-007 Fig. 401
3. Job Set-up
__________
Subtask 30-73-53-860-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the access platform is in position at the FWD cargo-compartment door 825.
Subtask 30-73-53-010-064
B. Get Access
(1)
Make sure that the FWD cargo-compartment door 825 is open (Ref. TASK 52-30-00-860-001).
(2)
Make sure that the CARGO COMPT LIGHT switch 6LU is at ON.
(3)
Make sure that, in the FWD cargo compartment, the following panel(s) is(are) removed: FOR 4DW 131GW, 131HW FOR 16DW 131HW FOR 335DW 131HW, 131SW
R 1EFF : 151-199, 401-499, 1 30-73-53Page 406 1 1 Config-2 Aug 01/05 1 1 1CES 1
Subtask 30-73-53-865-069
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R C/B NOT APPLICABLE
4. Procedure
_________
(Ref. Fig. 401/TASK 30-73-53-991-007)
Subtask 30-73-53-420-056
A. Installation of the Heater Elements WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1)
Clean the potable water line with CLEANING AGENTS (Material No. 11-001) and a lint free cloth.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Put the heater element (9) in position on the potable water line.
(4)
Attach the heater element (9) to the potable water line with the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001) (8) and with the heat-shrink sleeve (7).
(5)
Make sure that the electrical connectors are clean and in the correct condition.
(6)
Connect the three wires (10) of the heater element (9) to the terminal strip.
NOTE : Connect the electrical wires as identified during the removal
____
procedure.
(7) If necessary, install the potable-water de-icing sensor (10DW) (Ref. TASK 30-73-17-400-002).
R 1EFF : 151-199, 401-499, 1 30-73-53Page 407 1 1 Config-2 Aug 01/05 1 1 1CES 1
(8) Insulate all the potable water lines with the insulation sleeve (5).
NOTE : Make sure that the electrical connections do not touch the
____
insulation sleeve (5).
(9) Put BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001) (6) on the longitudinal cut of the insulation sleeve (5).
(10)
Install the insulation muffs (4), the adhesive tape and safety it with the velcro tape (3).
(11)
Install the spacers (1) and the clamps (2).
(12)
Attach the identification and warning labels with the new cable ties. NOTE : Do not damage the insulation sleeve (5) with the cable ties.
____
Subtask 30-73-53-865-070
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s): R C/B NOT APPLICABLE.
Subtask 30-73-53-720-055
C. Do the functional test of the potable-water ice protection (Ref. TASK 30-73-00-720-001).
5. Close-up
________
Subtask 30-73-53-410-056
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
In the FWD cargo compartment, install the access panel(s): FOR 4DW 131GW, 131HW FOR 16DW 131HW FOR 335DW 131HW, 131SW
(3)
Set the CARGO COMPT LIGHT switch 6LU to OFF.
R 1EFF : 151-199, 401-499, 1 30-73-53Page 408 1 1 Config-2 Aug 01/05 1 1 1CES 1
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM ICE AND RAIN PROTECTION 防冰和排雨2(119)
